Removing clear bra
#3
Registered User
iTrader: (4)
Join Date: Jul 2006
Location: norcal
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
I've been wondering the same thing since I picked up my '03 PPW Z earlier this week. The bra is in great condition, save the fact that it has unfortunately started to yellow.
I spoke with Pepi of Auto Supershield fame (south FL), and he assured me that they should come cleanly off if you let it heat up in the sun for a while, then slowly pull from one edge to the other at a 90 degree angle to the film. I still don't trust myself to do it, so I'll hopefully be having him take care of it all when I go in next week to get the windows tinted.
After seeing a handful of people loudly proclaiming that it will take the paint off !!!, I asked him about it, and he laughed. As long as you take your time, it should come off clean and without any residue. I'll report back after next week if I remember.
I spoke with Pepi of Auto Supershield fame (south FL), and he assured me that they should come cleanly off if you let it heat up in the sun for a while, then slowly pull from one edge to the other at a 90 degree angle to the film. I still don't trust myself to do it, so I'll hopefully be having him take care of it all when I go in next week to get the windows tinted.
After seeing a handful of people loudly proclaiming that it will take the paint off !!!, I asked him about it, and he laughed. As long as you take your time, it should come off clean and without any residue. I'll report back after next week if I remember.
#4
Registered User
Thread Starter
iTrader: (1)
Join Date: Jul 2006
Location: chandler, az
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by connman
I've been wondering the same thing since I picked up my '03 PPW Z earlier this week. The bra is in great condition, save the fact that it has unfortunately started to yellow.
I spoke with Pepi of Auto Supershield fame (south FL), and he assured me that they should come cleanly off if you let it heat up in the sun for a while, then slowly pull from one edge to the other at a 90 degree angle to the film. I still don't trust myself to do it, so I'll hopefully be having him take care of it all when I go in next week to get the windows tinted.
After seeing a handful of people loudly proclaiming that it will take the paint off !!!, I asked him about it, and he laughed. As long as you take your time, it should come off clean and without any residue. I'll report back after next week if I remember.
I spoke with Pepi of Auto Supershield fame (south FL), and he assured me that they should come cleanly off if you let it heat up in the sun for a while, then slowly pull from one edge to the other at a 90 degree angle to the film. I still don't trust myself to do it, so I'll hopefully be having him take care of it all when I go in next week to get the windows tinted.
After seeing a handful of people loudly proclaiming that it will take the paint off !!!, I asked him about it, and he laughed. As long as you take your time, it should come off clean and without any residue. I'll report back after next week if I remember.
#5
Registered User
iTrader: (43)
Join Date: Apr 2004
Location: Orlando
Posts: 675
Likes: 0
Received 0 Likes
on
0 Posts
I have taken my hood piece off. I had a rock hit it and tear through it, so I removed it. Let it sit in the sun for a bit, then started at one edge and started pulling slowly. Best tip I can give is don't pull from a corner diagonally, start at a corner and try to work one whole side off, then get a handful and pull across. It is a bit of a pain cause it's on there good, just have to be patient. I used 3M adhesive and wax remover to get rid of the excess adhesive. Oh, and wear gloves or something, cause it takes a lot of work and I got some blisters from doing it
#6
Registered User
iTrader: (43)
Join Date: Apr 2004
Location: Orlando
Posts: 675
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by trumanator3
ya, that'd be cool if you could let us know how it goes. also let us know if its at all noticable if the rest of the paint has faded at all compared to the paint that was underneath the bra
Trending Topics
#8
Registered User
Join Date: Aug 2004
Location: Atlanta
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by freeman
I was wondering this myself.
Also, how do you repair little tears in the plastic? I got some curb rash very small.
Also, how do you repair little tears in the plastic? I got some curb rash very small.
Removing the film should never pull factory OEM paint off no matter how you remove it. Pulling at a 45 to 90 degree angle, stretch the film off the car and that should keep most of the adhesive on the back of the film. Pepi is correct, be patient and keep the adhesive side and your hands wet, that will keep blisters from forming on your fingertips.
www.speedfilm.net
#9
I had a 3M authorized shop to replace a piece under the bottom of the door. When they pulled it off, some paint came off with it. I was not there to see how they did it. That was factory paint too.
#10
Registered User
I have experience pulling this crap off. Most people say to heat it up with a heat gun, and it does come off a bit easier... but leaves one hell of a mess. I pulled it off once when it was absolutely cold, and not a single piece of glue stayed. However i dont advise this for paint... these were headlight pieces.
#11
Registered User
Join Date: Aug 2004
Location: Atlanta
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ohw
I had a 3M authorized shop to replace a piece under the bottom of the door. When they pulled it off, some paint came off with it. I was not there to see how they did it. That was factory paint too.
About four years ago while replacing a piece of film that had lifted, paint come off a brand new BMW M3 mirror when the car was only days old. Research on the Beemer showed the car had been damaged at the port and the mirror had been knocked off and resprayed before the dealer even got the car. This happens often enough that most importers have a paint booth right there where the cars are off loaded from the ships.
I've been doing paint protection film for over six years and removed lots of film and the paint under the hood coming off is the only instance where I have seen true factory paint lift off with the film ( not counting the factory pieces ). Last week I replaced yellowed 3M film on a white C6 Corvette, the hood, fenders, mirrors, bumper, rockers and wheel wells without a bit of trouble with adhesive left behind or any paint issues.
Last edited by Speed 2000; 07-28-2006 at 04:43 AM.
#13
Originally Posted by Speed 2000
Under the bottom of the door? Was that a factory applied piece like just ahead of the rear wheels? I have seen paint come off from the underside of the hood before( basically where the sun never shines ) where the paint hadn't adhered properly, but just a small sliver. I have also seen paint come off when removing the factory pieces that were improperly installed. OEM paint protection film is applied way before the paint has cured and is dangerous to remove for that very reason.
....
....
#14
Registered User
iTrader: (4)
I have pulled smaller pieces of it off (mirrors, side skirts, and below the front grill) but not the bumper or the hood.
The key is to make sure the sure is as hot as can be. Preferably, with the car parked in the sun for a few hours. Gradually pry an edge until you can grab hold of it. Then in one smooth motion, start peeling it off. It's important not to stop until the entire piece is off. That can be tough if you are positioned incorrectly. Be sure to maintain the smooth momentum ALL THE WAY THROUGH.
The key is to make sure the sure is as hot as can be. Preferably, with the car parked in the sun for a few hours. Gradually pry an edge until you can grab hold of it. Then in one smooth motion, start peeling it off. It's important not to stop until the entire piece is off. That can be tough if you are positioned incorrectly. Be sure to maintain the smooth momentum ALL THE WAY THROUGH.
#16
Registered User
iTrader: (1)
Join Date: Dec 2004
Location: New York, NY
Posts: 2,632
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Chad68
Wow now I'm kinda glad I didn't get the clear bra.
#17
Registered User
iTrader: (4)
Originally Posted by highside107
Nah.. I would agree with you if you got a 1st or 2nd generation 3M clearbra that yellow'd. Newer ones are much nicer and obviously the technology has advanced over the years so this *probably* is not an issue anymore. I would still recommend getting one. Usually you can take it back to your installer who will take it off for you if need be.
The installer came to my home to install it so we chatted while he worked. According to him, in March of '06, 3M released a new formula of the clear bra compound that is meant to not yellow even after years of use. He said on a dark color like mine, yellowing is tough to see anyway, but on white and silver cars he has done with the old bra, slight yellowing is mildly noticeable after 3-4 months. With the new kind, he hasn't noticed that issue on cars he has done so far.
Thread
Thread Starter
Forum
Replies
Last Post
Gruppe-S
Body Interior
13
05-16-2016 10:42 PM
CFAUVEL
Exterior & Interior
3
10-01-2015 03:20 PM