kinetex V+ install and whistle
#1
Registered User
Thread Starter
iTrader: (1)
Join Date: Jul 2006
Location: redding,ca
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
kinetex V+ install and whistle
Hello guys
i am know i pretty new here, but have done lots of searching and few mods to the z. I recently installed the kinetix v+ plenum. I love the power it made. It seems to idle fine, sometimes pops or rough, but it sorta did this prior. But at part acceleration i get a whistle.
Do i have a intake leak. I am throwing a code too that i can't get to go away, this could be from my Test Pipes, although i have non fowlers in.
People think i have a damn turbo cause the sound. LOL
I want to race it tommarrow night so should i spend the time ripping the intake off and reinstalling.
I added Thin amount of RTV last time, should i do this again.
Any info is great.
Thanks
David
i am know i pretty new here, but have done lots of searching and few mods to the z. I recently installed the kinetix v+ plenum. I love the power it made. It seems to idle fine, sometimes pops or rough, but it sorta did this prior. But at part acceleration i get a whistle.
Do i have a intake leak. I am throwing a code too that i can't get to go away, this could be from my Test Pipes, although i have non fowlers in.
People think i have a damn turbo cause the sound. LOL
I want to race it tommarrow night so should i spend the time ripping the intake off and reinstalling.
I added Thin amount of RTV last time, should i do this again.
Any info is great.
Thanks
David
#3
Registered User
iTrader: (2)
Join Date: Nov 2006
Location: PHX
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
have a leak sumwherr... take it up the top of 2nd and the press the clutch in. if it dies on u its a pretty bad leak. jus run u hands all the way around the plenum and u should be able to feel the air... jus happened to me the other day when i installed my ssv.
#4
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
Spray starting fluid around the edges while its running and see if you hear a difference. Next , why did you RTV it ?? Last mine has a slight whistle to it too , its probably normal.
Last edited by terrasmak; 10-28-2007 at 01:46 AM.
#5
Registered User
Thread Starter
iTrader: (1)
Join Date: Jul 2006
Location: redding,ca
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by terrasmak
Spay starting fluid around the edges while its running and see if you hear a difference. Next , why did you RTV it ?? Last mine has a slight whistle to it too , its probably normal.
I went and bought some starting fluid and sprayed it around the edges and nothing, no engine sound change. I even held the rpms at 2500 too to see if it owuld do it.
I do have a whistle when shuting down from a tube coming out of the passenger side of the plenum. But seems normal. It just pops at idle a little bit, which i heard is normal.
I used rtv as i read it on a write up somewhere. it was a very thin bead.
The whistle is pretty loud but it is only at part throttle and between 1800-3000 rpm, full throttle does not do it.
Trending Topics
#8
Registered User
iTrader: (1)
Join Date: Dec 2004
Location: tucson.az
Posts: 638
Likes: 0
Received 0 Likes
on
0 Posts
I've had the V+ for 8K miles so far. 0 problems. There is a specific tightening pattern and torque specs for the plenum that need to be followed closely.
Also. periodic checking of torque specs in the designated order and adjusting accordingly may be a simple answer.
Kinetix was VERY helpful when I had questions during the installation process. Maybe call them??
Also. periodic checking of torque specs in the designated order and adjusting accordingly may be a simple answer.
Kinetix was VERY helpful when I had questions during the installation process. Maybe call them??
Last edited by jcpeyton; 10-27-2007 at 05:59 PM. Reason: Additional information
#9
Registered User
iTrader: (3)
Join Date: Oct 2010
Location: DFW Texas
Posts: 250
Likes: 0
Received 0 Likes
on
0 Posts
I didnt know there was any specific pattern to tighten the manifold down, but I do now... I have had mine for over a month and just used a t-handle allen wrench on mine to tighten it and have had no problems at all with it, I prob should get a tune but all I have done is the maifold and K&N intake other than that stock...
#10
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
#11
Registered User
iTrader: (3)
Join Date: Oct 2010
Location: DFW Texas
Posts: 250
Likes: 0
Received 0 Likes
on
0 Posts
I misread the title and pics don't always pop on my comp at work so there for I did not have any pics to look at at the time. I understand the difference between them now. My bad next time I'll try to use a comp that will show pics on every thread.
Thread
Thread Starter
Forum
Replies
Last Post
MAZ350
Brakes & Suspension (DIY)
33
09-21-2017 07:21 AM