FliPPER_Z

iTrader: (16)

LEDs and HIDs work very different. so no , its not gonna work.

MURDAH350

hmmmmm.... ok well good thing i didnt hook them up hahaha...... well any idea how i can get those mugs shining brighter? (the leds)

bmccann101

iTrader: (16)

in effort to keep the thread i started on track.. AHEM....

I have some updated work on my headlights using parts supplied by flipperz (ZLEDS)

I dont have them on the car yet, but at least i can show you the guts of what was done.

Ill post back some pics tomorrow ...

Cux350z

iTrader: (162)

I went 100% led in my headlights. You can dim them easily, change RGB colors and they are more efficient.

LEDS operate at typically low voltages and you have to add resistors to run them at the cars 12V. Running a ballast will not work and is not needed.

If you want a brighter LED just run higher voltage to it....but be careful because you are shortening the life and with enough voltage you destroy the LED.

bmccann101

iTrader: (16)

yep..all led is the way to roll.

speaking of which... im doing 10 (5 per side) frenched in 10watt projector leds in the bumper like the new rocket bunny frs bumpers ..that is not going to be cheap body work, but i want what i want lol..saving my electrical current for fuel pumps and fans and airbag compressors

taywan

iTrader: (53)

Dam. Reading up more.

Can somebody confirm please... the Ironman ring is what size max?? I personally called TRS and the guy put me on hold to ask coworkers w 350z s and they all said 100mm. Is this way too big too big for Ironman?

I ordered the 100mm BC the guy confirmed that was the correct size. Should I call them to get the 80mm??

taywan

iTrader: (53)

Ok, so got mine in...100mm will fit perfectly for those concerned like I was. Waiting on demon eye led to arrive along w new lenses and we're good to go! So exciting. Thanks OP and cux!!

bmccann101

iTrader: (16)

jesus thats bright.. i may have to upgrade later on.. again.

taywan

iTrader: (53)

That's the regular white led from trs. Cux noticed the bleed through so putting a coat of silver to hide that some.

Here's a pic w a coat and no more bleed through..

shyun1250

iTrader: (4)

I purchased the 90mm and 100mm.

I can confirm that its the 100mm for the iron man with the xbled.

Amenite

Just bought the 100mm for the xbled. Do you happen to know what the size is for the outside? as in if I was doing iron man mod as well as halo, what is the size of that halo ring? I read the whole thread and confused as **** on that size


EDIT: Halo ring would also be xbled

taywan

iTrader: (53)

Yellow jdm turn covers deleted and dimple plates deleted. Leds on 4 strips above in corners along w Ironman and blue demon. Sti-R lenses and brand new outside lenses swapped as well. Will get rid of that amber turn signal shine soon as well. Shaving the cf air duct and repainting entire front end soon enough. Shout out to cux.....Thanks 'bruh' ...

meanz

iTrader: (23)

Turned out great! Me next Cux!

Cux350z

iTrader: (162)

sob!


i still have to finish mine.

Get your shopping list from Taywan..

taywan

iTrader: (53)

Josh.... get the dam z back first boo. Can't mod that thing when it sits in the shop collecting dust fool.

Guitar Nut

80mm outside/100mm inside.

shyun1250

iTrader: (4)

Sorry for taking a while to reply.
From what I was told by Diode Dynamics, the outer is 80mm.
but then again it wasn't a XBled but rather a smd ring.

I'd still give the 80mm a go and see.
If it doesn't work out, hopefully TRS can exchange it.

Guitar Nut

An 80mm xbled will work fine for an outer halo. I attached a pic in my previous comment showing how it looks. I'm using a 80mm on the outside and a 100mm inside. Both are xbled's from TRS by the way.

Amenite

Thank you! That picture described everything I needed! and now I know the size too haha

Will post back after I am done with headlights. Damn nissan is taking forever to change the transmission valve covers. Been a week already without my baby

taywan

iTrader: (53)

Still diggin mine!!