FS:
07-16-2013, 10:11 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
07-22-2013, 12:44 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
07-26-2013, 10:42 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
08-02-2013, 07:58 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
08-08-2013, 01:33 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
In stock! Thanks for the sales!
08-09-2013, 05:23 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
08-14-2013, 12:57 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
08-16-2013, 10:26 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
08-19-2013, 12:58 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
08-21-2013, 12:31 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
08-23-2013, 11:20 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
Orders shipped! Pm's replied too!
08-28-2013, 10:46 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
Great product! Orders shipped!
09-04-2013, 07:25 AM
Registered User
Join Date: Mar 2011
Location: Copenhagen - Denmark - Europe
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
Would you say this is needed when building an NA setup with high compression pistons, cams and a little raised rev limiter? or would i be fine with stock bolts?
09-04-2013, 01:43 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
If you are going through the motor and raising compression I would recommend using L19's, they are also reusable in case you need to pull the head in the future.
Last edited by Dynosty; 09-06-2013 at 01:35 PM .
09-06-2013, 01:37 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
Orders shipped- Still in stock!
09-09-2013, 12:40 PM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
09-11-2013, 11:27 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
09-13-2013, 11:06 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
09-17-2013, 10:24 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
09-18-2013, 11:51 AM
Vendor - Former Vendor
Thread Starter
Join Date: Jan 2007
Location: Louisville, KY
Posts: 2,137
Likes: 0
Great product! BUY NOW!
09-04-2013, 07:25 AM
