Window drop issue.
03-13-2018, 06:12 PM
#1
New Member
Thread Starter
Window drop issue.
So I’m sure there is a thread on this somewhere but I couldn’t seem to locate it.
The issue I’m having is the driver side window does not drop the small amount it should when the door is opened so that it will not catch on the Exterior trim of the car when the door is closed.
The auto down feature works fine and window works fine in general but when activating the auto up feature it will go all the way up stop and then roll down to half way. This happens when the door is closed or open. The passenger side works as it should. So I replaced the “little nipple” (the one that controls the interior lights and is supposed to control the auto drop and up feature) for lack of a better tern that’s on the driver side with the one that’s on the passenger side since it works fine. There was no change the passenger side still dropped as it should and the driver side still did not work. One things to add the “little nipple” still does turn the interior lights on and off as it should.
I have tried the know reset methods with the control switch but have not tried removing the door panel to reach the actual switch on the motor.
Could this his be the motor or regulator being bad?
Car is an 07 350z enthusiast 6 mt
Thanks in advance.
The issue I’m having is the driver side window does not drop the small amount it should when the door is opened so that it will not catch on the Exterior trim of the car when the door is closed.
The auto down feature works fine and window works fine in general but when activating the auto up feature it will go all the way up stop and then roll down to half way. This happens when the door is closed or open. The passenger side works as it should. So I replaced the “little nipple” (the one that controls the interior lights and is supposed to control the auto drop and up feature) for lack of a better tern that’s on the driver side with the one that’s on the passenger side since it works fine. There was no change the passenger side still dropped as it should and the driver side still did not work. One things to add the “little nipple” still does turn the interior lights on and off as it should.
I have tried the know reset methods with the control switch but have not tried removing the door panel to reach the actual switch on the motor.
Could this his be the motor or regulator being bad?
Car is an 07 350z enthusiast 6 mt
Thanks in advance.
Last edited by WhiteDevil-Z; 03-13-2018 at 06:13 PM.
03-13-2018, 07:23 PM
#2
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
So I’m sure there is a thread on this somewhere but I couldn’t seem to locate it.
The issue I’m having is the driver side window does not drop the small amount it should when the door is opened so that it will not catch on the Exterior trim of the car when the door is closed.
The auto down feature works fine and window works fine in general but when activating the auto up feature it will go all the way up stop and then roll down to half way. This happens when the door is closed or open. The passenger side works as it should. So I replaced the “little nipple” (the one that controls the interior lights and is supposed to control the auto drop and up feature) for lack of a better tern that’s on the driver side with the one that’s on the passenger side since it works fine. There was no change the passenger side still dropped as it should and the driver side still did not work. One things to add the “little nipple” still does turn the interior lights on and off as it should.
I have tried the know reset methods with the control switch but have not tried removing the door panel to reach the actual switch on the motor.
Could this his be the motor or regulator being bad?
Car is an 07 350z enthusiast 6 mt
Thanks in advance.
The issue I’m having is the driver side window does not drop the small amount it should when the door is opened so that it will not catch on the Exterior trim of the car when the door is closed.
The auto down feature works fine and window works fine in general but when activating the auto up feature it will go all the way up stop and then roll down to half way. This happens when the door is closed or open. The passenger side works as it should. So I replaced the “little nipple” (the one that controls the interior lights and is supposed to control the auto drop and up feature) for lack of a better tern that’s on the driver side with the one that’s on the passenger side since it works fine. There was no change the passenger side still dropped as it should and the driver side still did not work. One things to add the “little nipple” still does turn the interior lights on and off as it should.
I have tried the know reset methods with the control switch but have not tried removing the door panel to reach the actual switch on the motor.
Could this his be the motor or regulator being bad?
Car is an 07 350z enthusiast 6 mt
Thanks in advance.
03-14-2018, 04:36 AM
#4
Also - While you're in there, it might be a good time to service(clean & lubricate) the regulator assembly and within the cable conduit that the window is driven by with some dry graphite lube.
03-17-2018, 02:38 PM
#5
New Member
Thread Starter
Thanks all for the reply’s you are the real mvps. Oh @travlee thanks for the picture by the way. But I was not sure if both issues were related to the same thing but either way +1 for trolling. 😂
03-17-2018, 02:55 PM
#7
New Member
Thread Starter
Trending Topics
03-14-2020, 09:00 AM
#8
New Member
Join Date: Jan 2020
Location: oregon city
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
No drop.
Please help, I have followed the reset procedure and it goes fine. But the window does not drop when the door opens. Please let me know some ideas about why this is happening. Thank you.
03-15-2020, 08:29 AM
#9
General & Tech Moderator
MY350Z.COM
MY350Z.COM
03-15-2020, 09:02 AM
#10
New Member
Join Date: Jan 2020
Location: oregon city
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
03-15-2020, 09:12 AM
#11
General & Tech Moderator
MY350Z.COM
MY350Z.COM
The older style motors had a button to push (on the motor). I remember having trouble getting the reset switch to acknowledge being pressed. Ended up using a 6" socket extension. Gl!
05-31-2023, 04:58 AM
#12
Registered User
Join Date: May 2023
Location: netherlands
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
I stumbled upon this post and decided to revive this thread. While I'm not an expert, it's possible that the motor or regulator might be the cause. Before going further, you could try resetting the control switch. If that doesn't work, consider seeking help from a professional or someone experienced in car repairs. They can diagnose the problem accurately and provide the best solution. Additionally, if you want to ensure the safety and comfort of your little ones, it's a good idea to explore the market for the best baby car sun shades. These shades can provide excellent protection from the sun's glare and harmful UV rays, creating a more enjoyable and safer environment for your children during car rides.
Last edited by AdamBurgess; 06-02-2023 at 03:49 AM.
Thread
Thread Starter
Forum
Replies
Last Post