Alignment numbers after springs install..not good
#43
Registered User
iTrader: (2)
I had the camber arms installed at the shop because they did an alignment right after, so what the heck. But they aren't too hard, they have 1 bolt on each end, end of story.
As chilton would write it :
A) Remove existing bolts
B) Remove existing arm
C) Install is reverse of removal...
As chilton would write it :
A) Remove existing bolts
B) Remove existing arm
C) Install is reverse of removal...
#44
Registered User
iTrader: (25)
Join Date: Oct 2003
Location: Orlando, FL
Posts: 2,864
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by slaponte
I had the camber arms installed at the shop because they did an alignment right after, so what the heck. But they aren't too hard, they have 1 bolt on each end, end of story.
As chilton would write it :
A) Remove existing bolts
B) Remove existing arm
C) Install is reverse of removal...
I had the camber arms installed at the shop because they did an alignment right after, so what the heck. But they aren't too hard, they have 1 bolt on each end, end of story.
As chilton would write it :
A) Remove existing bolts
B) Remove existing arm
C) Install is reverse of removal...
#45
Registered User
iTrader: (5)
Join Date: Feb 2004
Location: Fort Lauderdale, FL
Posts: 702
Likes: 0
Received 0 Likes
on
0 Posts
wouldnt the tein S TECH springs not cause any camber issues? it gives you a decent drop, and stays below the .8" drop that will cause the camber issues.
TEIN S-TECH SPRINGS
Spring rate: Front 386lbs Rear 402lbs
Lowers: Front -0.7" Rear -0.6"
TEIN S-TECH SPRINGS
Spring rate: Front 386lbs Rear 402lbs
Lowers: Front -0.7" Rear -0.6"
#46
Registered User
iTrader: (2)
For the rears, no, you shouldn't have to. But they did because I was having the tires rotated, etc anyway. You can reach it from behind/below the car, but could be more cumbersome than necessary.
For the fronts, most definetly. Tires, struts had to be loosened, strut bar, etc just to get to those two bolts...
For the fronts, most definetly. Tires, struts had to be loosened, strut bar, etc just to get to those two bolts...
#48
Registered User
iTrader: (2)
You have one now.
The rear toe adjustment on the car is a bolt with a washer that is "offset": it is wider on one side than the other. As you turn it, that offset pushes the arm in or out, by a few milimiters.
A larger cam bolt will have a larger offset, thus allowing more adjustment. The ones I got have a -3 to +3 adjustment.
I got mine from here :
Import Auto Parts Direct
Note that they sell a kit with camber and toe. If you email them they sell you the Toe bolts alone.
The larger Toe bolts do require that you enlarge the hole on the arm where they go. Instructions and template are included with the bolts.
The rear toe adjustment on the car is a bolt with a washer that is "offset": it is wider on one side than the other. As you turn it, that offset pushes the arm in or out, by a few milimiters.
A larger cam bolt will have a larger offset, thus allowing more adjustment. The ones I got have a -3 to +3 adjustment.
I got mine from here :
Import Auto Parts Direct
Note that they sell a kit with camber and toe. If you email them they sell you the Toe bolts alone.
The larger Toe bolts do require that you enlarge the hole on the arm where they go. Instructions and template are included with the bolts.
Thread
Thread Starter
Forum
Replies
Last Post
Lt_Ballzacki
Brakes & Suspension
39
08-06-2021 06:19 AM