My 2jz swap
#201
New Member
Thread Starter
.
Update.
so the car started smoking on decel after a pull a few months ago and slowly it became worse and worse took the turbo off trubo seals where shot and the Center housing of the trubo was scored really bad tryed to rebuild it and it didnt help one bit. I'm currently out of the country for a year but when I get back I'm getting a turbo smart turbo oil regulator and a pt 7275 turbo. I'm hoping its actually makes 1k.
Last edited by chase z; 12-16-2019 at 02:19 AM.
#202
Update. Smoking
so the car started smoking on decel after a pull a few months ago and slowly it became worse and worse took the turbo off trubo seals where shot and the Center housing of the trubo was scored really bad tryed to rebuild it and it didnt help one bit. I'm currently out of the country for a year but when I get back I'm getting a turbo smart turbo oil regulator and a pt 7275 turbo. I'm hoping its actually makes 1k.
so the car started smoking on decel after a pull a few months ago and slowly it became worse and worse took the turbo off trubo seals where shot and the Center housing of the trubo was scored really bad tryed to rebuild it and it didnt help one bit. I'm currently out of the country for a year but when I get back I'm getting a turbo smart turbo oil regulator and a pt 7275 turbo. I'm hoping its actually makes 1k.
#203
350Z-holic
iTrader: (13)
Look up Reagan's 1.5jz swap thread too...
The following users liked this post:
Raggan (03-09-2020)
#204
New Member
Thread Starter
loj is working on a 2j swap kit and if its anything like there ls swap kit it would definitely be worth the wait there stuff comes with everything.
#205
350Z-holic
iTrader: (13)
Any updates on the car Chase? still out of the country?
#206
New Member
Thread Starter
yes I got back about a month ago now. Decided to just get a new Center cartridge for the bw369sxe. I also got the trubo smart turbo oil pressure ragalator. I installed all of that and drove it around about 80ish miles over the last few weekends on pump gas at 14psi. Feels pretty strong but I have e50 in the tank now and have it turned up to 18.5 psi letting the autotune clean up the rich under boost cells . Once I have over e60 in the tank I will slowly trun it up all the way to high 20s low 30s.
The following 2 users liked this post by chase z:
bealljk (04-12-2020),
rustyschopshop (04-12-2020)
The following users liked this post:
bealljk (04-28-2020)
The following 2 users liked this post by chase z:
bealljk (06-26-2021),
rustyschopshop (09-08-2021)
#209
New Member
Thread Starter
I was feeling alot of movement in the transmission so I decided to ad some 94a urethane to the oem tran mount bushing
Last edited by chase z; 05-03-2020 at 05:01 PM.
The following users liked this post:
Raggan (05-03-2020)
The following users liked this post:
bealljk (05-09-2020)
#211
350Z-holic
iTrader: (13)
The following users liked this post:
bealljk (05-09-2020)
#213
New Member
Thread Starter
I got a to good to pass up deal on a older smithy mill/ lathe combo. A few little parts have to be ordered, then we will see what I can make!
Last edited by chase z; 05-14-2020 at 06:30 PM.
#214
New Member
Thread Starter
I haven't posted any updates in quite awhile. Moved to a new house with a better separate shop layout and collected a few parts for a updated setup, bw476sxe trubo, oem radiator replacement with factory radiator support, oem ac components and moving the motor back about 3.5 to 4 inches so i can fit the oem ac / coolant components.
Last edited by chase z; 01-06-2021 at 08:33 AM.
The following users liked this post:
bealljk (01-06-2021)
The following 3 users liked this post by chase z:
The following users liked this post:
rustyschopshop (09-08-2021)
The following 2 users liked this post by chase z:
bealljk (09-06-2021),
rustyschopshop (09-08-2021)
The following users liked this post:
bealljk (09-13-2021)
The following 2 users liked this post by chase z:
GreyZ (08-29-2022),
PeterPotatoes (09-03-2022)
The following users liked this post:
bruthaboost (01-17-2024)
Thread
Thread Starter
Forum
Replies
Last Post
atomicgoofball
Mid-Atlantic
14
05-06-2008 08:42 PM
InjectedPerformance
Forced Induction
76
05-29-2005 04:22 PM