R&D Factory Valve Cover Gasket kit is back !!!!!!!!!
15 Attachment(s)
R&D Factory is back ! At R&D Factory we service many Nissans and Infinities daily and run into same valve cover/spark plug o-ring leak. About 75% of the vehicles that we serve have same problems. Even though its money out of customers pocket after spending so much money on these valve covers we were thinking there has to be a way to cut the cost so here we are. R&D has come out the kit will come with both driver and passenger side valve cover gasket, six o-ring gasket and a simple instruction how to replace them.your warranty should and will cover leaking valve cover o-rings grommets. we do advise you to check for leak before your warranty is over.... the whole idea of us making these o-rings grommets were for those who have leaking o-rings grommets yet their warranty is already over. we do drill out the old o-ring grommets with hole saw size 2 inch. its is slightly bigger than the existing hole and slightly smaller than the o-ring....please pm us if you have any further questions....thank you
1.$75 for 6 Grommets (O-ring gasket) http://i14.photobucket.com/albums/a3...psb5348766.jpg 2.$120 for 6 Grommets (O-ring gasket) and OEM valve cover gaskets (both side), PCV Valve o-ring Attachment 435709 The video link . Here is a DIY Instructions on how to replace the OEM seals on your Nissan VQ engine. 1- THIS IS A SIMPLE HOLE SAW (SIZE 2 INCH) THAT YOU CAN BUY FROM MOST HARDWARE STORE. WE GOT OURS FROM ACE HARDWARE AND IT WAS $7-11. Attachment 435711 2- THIS IS HOW YOUR VALVE COVER LOOKS WHEN YOU TAKE IT OFF OF YOUR ENGINE Attachment 435712 NOTE PICTURE SHOWN MOST LEFT SPARK PLUG HOLE DRILLED. 3- WARNING “PLEASE DO NOT REMOVE BAFFLE PLATE” WARNING Attachment 435713 4- POSITION THE HOLE-SAW CONCENTRIC TO SPARKPLUG HOLE AND DRILL BAFFLE PLATE SLOWLY AND CAREFULLY. Attachment 435714 5- YOU WILL ONLY NEED TO DRILL JUST ENOUGH TO DRILL THROUGH THE BAFFLE PLATE (WE CLEANED UP ALL THE DEBRIS TO SHOW YOU CLEAR PICTURE DRILL ALL 6 POSITIONS AND CLEAN OFF DEBRIS WHEN DONE. Attachment 435715 Attachment 435716 6- NOW YOU WILL BE ABLE TO POP OUT THE OLD O-RING GROMMET OUT OF THE VALVE COVER. PLEASE REPEAT 6 TIMES. Attachment 435717 Attachment 435716 7- THIS IS WHAT IT WOULD LOOK LIKE WITH THE O-RING GROMMET OUT Attachment 435716 8- USE BLACK RTV SILICONE ON TOP SIDE OF THE NEW O-RING GROMMET (WE USED CLEAR ON OUR DEMO PICTURE SO YOU CAN SEE BETTER) Attachment 435720 9- PLACE THE NEW O-RING GASKET IN TO THE HOLE. NOW YOU ARE READY TO RE-INSTALL YOUR VALVE COVER GASKET TO YOUR ENGINE. Attachment 435721 Attachment 435722 [ FOR MORE INFO PLEASE CALL R&D FACTORY OR VIST www.rndfactory.com Attachment 435723 R&D Factory 5648 Schaefer Ave Chino , CA 91710 (909)287-3511 www.rndfactory.com |
ttt
|
ttt , thanks
|
ttt
|
ttt
|
Just pm'd you. I really need these to get the car back on the road.
|
Originally Posted by kouki_420
(Post 10351475)
Just pm'd you. I really need these to get the car back on the road.
|
How to video is up .
|
What's the difference in this product and legion fabrications?
|
2 Attachment(s)
A new alignment tool will be add to the DIT kit for better and easier to make a perfect hole.
Attachment 406402Attachment 406403 |
ttt
|
TTT. thanks
|
ttt
|
NEW DIY VIDEO
|
to the top
|
i have a set of valve covers for sale. i dont know if they leak.
|
Originally Posted by blAk mAx
(Post 10394412)
i have a set of valve covers for sale. i dont know if they leak.
|
sure
|
Originally Posted by blAk mAx
(Post 10394469)
sure
|
Nice guys!!!
|
All times are GMT -8. The time now is 01:22 PM. |
© 2024 MH Sub I, LLC dba Internet Brands