|
How to Exchange Hi Beam Lamps
I didn't see a how to on this simple modification so I thought I'd contribute one.
The HID projector bulbs on the Z are plenty bright enough but I found the conventional 55 W Halgen hi beams to be a bit yellow compared to the HID's and a bit under powered. After shopping around I picked up a set of SuperBeam EX 4500K lamps that run 100 Watts from autohalogen.com for $34.75 a pair. The bulb is an H7 and the total change out takes about as much time as changing a tire plus a few more minutes. Here's a picture showing the difference beween the two lamps. http://i6.photobucket.com/albums/y21...60/HiBeam1.jpg And a close up. http://i6.photobucket.com/albums/y21...60/HiBeam2.jpg Now how to do the procedure. First remove the tire to expose the front plastic liner. You'll need to remove three plastic clips using a small flat blade screw driver. You simply pry out the center pin and pull the whole assemble out. There is only one screw that you'll need to remove. I removed two more now at the bottom of the liner to get better pictures. Note: I've got the rear splash panel off to install some sound deadening materal, you do not have to remove this panel for the headlight work. http://i6.photobucket.com/albums/y21...60/HiBeam3.jpg Pulling the liner down and out of the way you'll expose the head lights - the projector and hi beam are under the light gray plastic disk. http://i6.photobucket.com/albums/y21...60/HiBeam4.jpg Rotate this cup clockwise about 1 inch and the disk should come lose. A rubber "O" ring protects the lamps from water thrown from the wheel. http://i6.photobucket.com/albums/y21...60/HiBeam5.jpg With the gray plastic disk removed you can get to the hi beam lamp. It's held in place with a spring clip that has one leg sticking out. Push this leg down and then rotate it upwards a bit to unlatch it from it's keeper. At this time I put clean cotton gloves on to protect both the old and new bulbs. http://i6.photobucket.com/albums/y21...60/HiBeam6.jpg Here's the stock and superbeam bulb side-by-side along with the work gloves and the inside of the gray plastic dish showing the "O" ring. I'm keeping the old bulbs as a spare in case I blow one of the replacements. http://i6.photobucket.com/albums/y21...60/HiBeam7.jpg The blue of the light is a bit different and looks good on my super black and would probably work on a Daytona blue as well. http://i6.photobucket.com/albums/y21...60/HiBeam8.jpg The 100W lights are a bit brighter and they cast a cleaner whiter light than the stock ones. Paul |
good write up, ive been thinking about doing this, but i cant get by the blue bulbs in the housing. what do you forumites thing the best option would be? silver stars?
|
Excellent write-up. This definitely has to be put under the "Tech & How-To" section.
|
Be careful with those blue bulbs. I've had past experience with the blue bulbs shattering, and getting stuck with the little blue glass pieces inside the headlight. Not those specifically, but the blue-colored glass bulbs in general.
|
Yeah, I've seen Halogen bulbs as cheap as $7. All halogen bulbs are sensitive to the oil in your hands so you have to wear clean gloves when handling them. The oil will act as a hot spot and can cause the bulb to pop.
|
do you have the direct link to the product Paul?
|
isnt it bad to run 100watt bulbs? i know that on a lot of hondas, those guys have problems running 100watt bulbs and they tend to burn up the wires, since your running almost double what stock is?
iono just thought id mention it =) looks better than stock, thats for sure haha |
:confused: where are those pics!!!!!!!!!!
|
btw, both bulbs are halogen bulbs.
|
| All times are GMT -8. The time now is 06:31 AM. |
© 2024 MH Sub I, LLC dba Internet Brands