Yeah that 15lbs seems like a conservative estimate, I pulled the wiring harness that had no purpose also it was 1/2 lb and then cleaned up the other sides wiring also... I cant believe they ran a harness from the front to back with nothing plugged into it. And it took some serious brain strain for my dumb ass to figure out how to unhook it...
https://cimg2.ibsrv.net/gimg/my350z....9954cf3fbd.jpg I dont think my scale Is very accurate for light weights. |
That looks like the navigation harness that i pulled out last year.
|
I believe thats what that harness was, I guess it wasnt needed because it wasnt hooked to anything.
I just noticed that I have the same scale as op... Dicks sporting goods $10 purchase ftw Took off the rear tie down hook... About a pount and a half. https://cimg5.ibsrv.net/gimg/my350z....59269ff5e3.jpg |
4 Attachment(s)
(as mentioned by dboyzalter above) my non-branded fiberglass/carbon hatch is right at 22lbs and the glass came in at 15lbs
Glass(bathroom scale): Attachment 384328 Glass(fish scale): Attachment 384329 Hatch only(bathroom scale): Attachment 384330 Hatch only (fish scale): Attachment 384331 |
Originally Posted by dboyzalter
(Post 10806248)
I believe thats what that harness was, I guess it wasnt needed because it wasnt hooked to anything.
I just noticed that I have the same scale as op... Dicks sporting goods $10 purchase ftw Took off the rear tie down hook... About a pount and a half. https://cimg5.ibsrv.net/gimg/my350z....59269ff5e3.jpg 2.2lbs https://cimg7.ibsrv.net/gimg/my350z....ed4920f43e.jpg |
Has anyone weighed the fuel tank?
|
Originally Posted by bealljk
(Post 10863769)
Has anyone weighed the fuel tank?
Probably not more than 20 lbs guesstimate... Ac compressor feels like a lot but only a little over 7 lbs https://cimg1.ibsrv.net/gimg/my350z....b3e94be3eb.jpg Not needed pully 3.4 https://cimg2.ibsrv.net/gimg/my350z....f8b560a8c1.jpg Stock manifold 6.8 https://cimg3.ibsrv.net/gimg/my350z....565907af8b.jpg Brembo front caliper 7.4 https://cimg4.ibsrv.net/gimg/my350z....85af3a076a.jpg Brembo front rotor 20 https://cimg5.ibsrv.net/gimg/my350z....a92b6d2b03.jpg |
1 Attachment(s)
for the archive - transmission cross-member, OEM trans mount & weighted bolt - 8lbs
cross member was 5.5lbs mount 1.5lbs weighted bolt 1lb Attachment 382899 |
|
https://cimg4.ibsrv.net/gimg/my350z....dc39367288.jpg
In conjunction with post #122 on page 3 (of this thread). Passenger side window glass 10.4lbs Passenger side window regulator - 5.0lbs Passenger side plate (verifying post #122) 4.5lbs +/- 20lbs per side https://cimg5.ibsrv.net/gimg/my350z....0e10680d99.jpg https://cimg6.ibsrv.net/gimg/my350z....1f3a7f8d54.jpg |
picked these off the CL ... need a daily driver set of wheels. I believe they are the g37 sport wheels by enkei 18x8 with a 43mm offset (cleared my AP 4piston by about 1/4")
https://cimg9.ibsrv.net/gimg/my350z....92b1f384f8.jpg 22.71 lbs / 23lbs |
I don't remember the total weights but I do remember the difference between the rear hatch OEM and the Siebon dry carbon fiber one is 36 pounds and that in not accounting for that weight they mount to the underside from the factory hatch.
|
Originally Posted by Rick*K
(Post 10974153)
I don't remember the total weights but I do remember the difference between the rear hatch OEM and the Siebon dry carbon fiber one is 36 pounds and that in not accounting for that weight they mount to the underside from the factory hatch.
https://cimg4.ibsrv.net/gimg/my350z....f5d742379.jpeg Weight of the gas tank: 39lbs with basket and driver side level gauge https://cimg8.ibsrv.net/gimg/my350z....277abbfa9.jpeg https://cimg1.ibsrv.net/gimg/my350z....bc015975e.jpeg https://cimg3.ibsrv.net/gimg/my350z....91a95538e.jpeg |
Incase anyone is wondering ... the subframe (by itself) is right around 40lbs.
https://cimg5.ibsrv.net/gimg/my350z....63509f0e9.jpeg https://cimg7.ibsrv.net/gimg/my350z....7415f460d.jpeg |
Anyone knows the weigth of the roof? Thinking about making a carbon one.
|
A carbon copy of a hood weighs ~1-2lbs more than the factory hood. I'm assuming this would be the same result from the roof panel
|
The steel roof is a structural section of the Z33 monocoque. You don't want to remove it without a way to properly bond a replacement section to the chassis.
|
I tried closing a roof panel bc I forked mine out and what DK said ... the panel is very very very difficult to cut out ... I had that black parts car z33 and I chopped the entire roof section out and could not cut the panel out ...
but it is indeed crazy heavy bc the structural element of the roof ... |
All times are GMT -8. The time now is 03:42 AM. |
© 2024 MH Sub I, LLC dba Internet Brands