2007+ OEM hood?
Some punk drizzled what looks to be a thin layer of bleach or something in a torn heart shape on my hood. It is very faint but noticeable. I'll post a pic soon.
Would one of these bubble hoods fit on my 2004 350z? I assume it would. https://cimg1.ibsrv.net/gimg/my350z....de71126ff1.jpg |
Yes. All hoods are interchangeable between the 350z
|
^^^ No they are not. You can not put a DE hood onto an HR Z without clearance issues.
Maybe you should stop breaking young girls' hearts, 'Pussologist'. |
^this gentleman is correct^
Yes, an 07-08 HR hood with fit on a 03-06 DE and Rev-Up. |
Originally Posted by pyshin
(Post 10509628)
^^^ No they are not. You can not put a DE hood onto an HR Z without clearance issues.
Maybe you should stop breaking young girls' hearts, 'Pussologist'. |
^^^ Doesn't matter if someone would ever want to; the impossibility alone means that they are NOT interchangeable.
|
Originally Posted by craig12895
(Post 10509648)
Why would anybody even want to do that?
|
Well I did not know that the HR actually stuck up more than the DE did and that the DE hood did not fit on the HR.
Thanks for the knowledge gents |
the reason for the bulge is the HR motor sits higher
|
This is why I'm right. Thanks Trav
|
you know, if i remember tonight, i will lay a board on my strut bar (so it goes to if not over the fenders) to see how much higher it is, i am curious now
|
Originally Posted by pyshin
(Post 10509628)
^^^ No they are not. You can not put a DE hood onto an HR Z without clearance issues.
Maybe you should stop breaking young girls' hearts, 'Pussologist'. :icon17: Might also want to figure out what you did for someone to vandalize your car, they will probably try something else |
Originally Posted by travlee
(Post 10509692)
you know, if i remember tonight, i will lay a board on my strut bar (so it goes to if not over the fenders) to see how much higher it is, i am curious now
|
Originally Posted by craig12895
(Post 10509751)
In for pictures of you planking on your HR
|
Originally Posted by travlee
(Post 10509757)
haha, i just might. scarfing down my salad, then running to the garage to measure
|
are you spying on me through my webcam??? rude (haha)
|
^ so is the plank for eating a salad ya wuss
|
Originally Posted by travlee
(Post 10509766)
are you spying on me through my webcam??? rude (haha)
|
Originally Posted by RUNWDVL
(Post 10509767)
^ so is the plank for eating a salad ya wuss
|
Originally Posted by craig12895
(Post 10509768)
Well you put tape over the webcam but you looked over the fact it was clear tape
|
okay, so i put a board on top of the engine cover right behind the strut bar, and another resting on the bolts holding the front of the engine cover on and resting against oil dipstick. i put painters tape on the body line and measured at the highest point of the fender (and i think the fenders are the same for all years)
https://cimg5.ibsrv.net/gimg/my350z....cfc363dfce.jpg https://cimg8.ibsrv.net/gimg/my350z....d903004a9d.jpg https://cimg9.ibsrv.net/gimg/my350z....4ccbcf865a.jpg this is the rear one https://cimg0.ibsrv.net/gimg/my350z....2a5f4e1253.jpg this is the front board https://cimg2.ibsrv.net/gimg/my350z....87682d2eea.jpg was a pain to get up there |
I can't believe it is raised that much.
And I'm going to blow up this picture and hang it on my ceiling. (Im thinking 6'x4' will do) |
Now you look like a pale Dr Evil...
|
now i want sharks with freakin lasers
|
HA!
|
:icon17:
This thread suprisingly delivers |
you're welcome.........
but in all honesty, this is prob some good info for people out there that don't know the difference i still see people ask what is a DE and an HR... |
All times are GMT -8. The time now is 10:49 PM. |
© 2024 MH Sub I, LLC dba Internet Brands