Upper plenum project 75mm Maxima TB
#161
New Member
iTrader: (2)
Well, the shop I went to before is now closed-ish and sold their dyno. I went to Rev works to get retuned. I had the same tuner as before, "MTuned" .The numbers are 237hp /215 tq. Its lower than before but it was another dyno.
So sadly there are no magic numbers to show an increase; however I love how it feels now.
Edit: Here is the graph.
So sadly there are no magic numbers to show an increase; however I love how it feels now.
Edit: Here is the graph.
Last edited by MatthewBouchard; 04-05-2017 at 07:31 AM.
The following users liked this post:
06platinumG (01-10-2018)
#162
New Member
iTrader: (26)
I don't have before or after dynos, but after I added a 3 inch intake and 3 inch maf to this setup, I picked up around 2-3 mph on my trap speed. Can't remember the DAs, but just to give a somewhat objective view of this mod. It definitely seems to work with the added breathing modifications.
Last edited by BakaN20; 04-04-2017 at 09:34 PM.
#163
Registered User
- I bought cockyZ's upper intake from him last year. It was delivered shortly after I paid for it. It has been collecting dust for the past year while I tried sorting out existing issues with the car. He is not accepting Private Messages, so I am posting on his thread.
Fast forward to April 2017. My car with a new rebuilt engine has put 331 WHP down on a Mustang dyno.
On to the pieced together stock-ish VQ35DE...
-Rebuilt engine
-Stock bottom end from a REV UP (Pistons, rods, block, crankshaft)
-Stock Non-Revup Heads
-Upgraded ARP Rod Bolts
-New Bearings
-New rings, etc...
-Revup Oil Pump
-PPE Longtube headers
-Single 3 " Agency Power Exhaust
-JWT C8 Cams and Springs
with stock throttle body, upper intake manifold, *ported revup lower, and Momentum intake and UPREV dyno tuning...
-331 WHP on a Mustang Dyno!! (Without this modified upper intake)
Fuel cut is set to 7000 rpm due to the stock rotating assembly. Needless to say I am very pleased with the numbers based upon the relatively mild cams and low 7000 RPM redline. It is still increasing power at fuel cut. I will try and post the dyno chart in the next couple days.
-I will be testing this modified intake manifold within the next couple weeks. I think it will show definitively whether it is a winner. C8 cams, PPE headers, Large intake, your upper intake, ported rev up lower and ported lower intake manifold, UP rev tuning, and full exhaust with no restriction. Revving to 7000 rpm...lets see how this goes!!
Thank you for coming up with this design...I am excitement to see some results!
Fast forward to April 2017. My car with a new rebuilt engine has put 331 WHP down on a Mustang dyno.
On to the pieced together stock-ish VQ35DE...
-Rebuilt engine
-Stock bottom end from a REV UP (Pistons, rods, block, crankshaft)
-Stock Non-Revup Heads
-Upgraded ARP Rod Bolts
-New Bearings
-New rings, etc...
-Revup Oil Pump
-PPE Longtube headers
-Single 3 " Agency Power Exhaust
-JWT C8 Cams and Springs
with stock throttle body, upper intake manifold, *ported revup lower, and Momentum intake and UPREV dyno tuning...
-331 WHP on a Mustang Dyno!! (Without this modified upper intake)
Fuel cut is set to 7000 rpm due to the stock rotating assembly. Needless to say I am very pleased with the numbers based upon the relatively mild cams and low 7000 RPM redline. It is still increasing power at fuel cut. I will try and post the dyno chart in the next couple days.
-I will be testing this modified intake manifold within the next couple weeks. I think it will show definitively whether it is a winner. C8 cams, PPE headers, Large intake, your upper intake, ported rev up lower and ported lower intake manifold, UP rev tuning, and full exhaust with no restriction. Revving to 7000 rpm...lets see how this goes!!
Thank you for coming up with this design...I am excitement to see some results!
The following users liked this post:
Desert Z (05-10-2017)
#164
New Member
iTrader: (3)
- I bought cockyZ's upper intake from him last year. It was delivered shortly after I paid for it. It has been collecting dust for the past year while I tried sorting out existing issues with the car. He is not accepting Private Messages, so I am posting on his thread.
Fast forward to April 2017. My car with a new rebuilt engine has put 331 WHP down on a Mustang dyno.
On to the pieced together stock-ish VQ35DE...
-Rebuilt engine
-Stock bottom end from a REV UP (Pistons, rods, block, crankshaft)
-Stock Non-Revup Heads
-Upgraded ARP Rod Bolts
-New Bearings
-New rings, etc...
-Revup Oil Pump
-PPE Longtube headers
-Single 3 " Agency Power Exhaust
-JWT C8 Cams and Springs
with stock throttle body, upper intake manifold, *ported revup lower, and Momentum intake and UPREV dyno tuning...
-331 WHP on a Mustang Dyno!! (Without this modified upper intake)
Fuel cut is set to 7000 rpm due to the stock rotating assembly. Needless to say I am very pleased with the numbers based upon the relatively mild cams and low 7000 RPM redline. It is still increasing power at fuel cut. I will try and post the dyno chart in the next couple days.
-I will be testing this modified intake manifold within the next couple weeks. I think it will show definitively whether it is a winner. C8 cams, PPE headers, Large intake, your upper intake, ported rev up lower and ported lower intake manifold, UP rev tuning, and full exhaust with no restriction. Revving to 7000 rpm...lets see how this goes!!
Thank you for coming up with this design...I am excitement to see some results!
Fast forward to April 2017. My car with a new rebuilt engine has put 331 WHP down on a Mustang dyno.
On to the pieced together stock-ish VQ35DE...
-Rebuilt engine
-Stock bottom end from a REV UP (Pistons, rods, block, crankshaft)
-Stock Non-Revup Heads
-Upgraded ARP Rod Bolts
-New Bearings
-New rings, etc...
-Revup Oil Pump
-PPE Longtube headers
-Single 3 " Agency Power Exhaust
-JWT C8 Cams and Springs
with stock throttle body, upper intake manifold, *ported revup lower, and Momentum intake and UPREV dyno tuning...
-331 WHP on a Mustang Dyno!! (Without this modified upper intake)
Fuel cut is set to 7000 rpm due to the stock rotating assembly. Needless to say I am very pleased with the numbers based upon the relatively mild cams and low 7000 RPM redline. It is still increasing power at fuel cut. I will try and post the dyno chart in the next couple days.
-I will be testing this modified intake manifold within the next couple weeks. I think it will show definitively whether it is a winner. C8 cams, PPE headers, Large intake, your upper intake, ported rev up lower and ported lower intake manifold, UP rev tuning, and full exhaust with no restriction. Revving to 7000 rpm...lets see how this goes!!
Thank you for coming up with this design...I am excitement to see some results!
#165
New Member
My build is similar to dms_mikey's - my z has Z1 Motorsport's stage 2 headwork with C8 cams. My non-revup made 300 whp on their dyno, and drops off fairly sharp. Can this plenum mod accommodate the NWP 75mm throttle body? Or would I definitely need to sell it to install the 75mm Maxima tb?
The following users liked this post:
jellofuel (07-11-2017)
#167
My build is similar to dms_mikey's - my z has Z1 Motorsport's stage 2 headwork with C8 cams. My non-revup made 300 whp on their dyno, and drops off fairly sharp. Can this plenum mod accommodate the NWP 75mm throttle body? Or would I definitely need to sell it to install the 75mm Maxima tb?
The following users liked this post:
jellofuel (07-11-2017)
#171
New Member
- I bought cockyZ's upper intake from him last year. It was delivered shortly after I paid for it. It has been collecting dust for the past year while I tried sorting out existing issues with the car. He is not accepting Private Messages, so I am posting on his thread.
Fast forward to April 2017. My car with a new rebuilt engine has put 331 WHP down on a Mustang dyno.
On to the pieced together stock-ish VQ35DE...
-Rebuilt engine
-Stock bottom end from a REV UP (Pistons, rods, block, crankshaft)
-Stock Non-Revup Heads
-Upgraded ARP Rod Bolts
-New Bearings
-New rings, etc...
-Revup Oil Pump
-PPE Longtube headers
-Single 3 " Agency Power Exhaust
-JWT C8 Cams and Springs
with stock throttle body, upper intake manifold, *ported revup lower, and Momentum intake and UPREV dyno tuning...
-331 WHP on a Mustang Dyno!! (Without this modified upper intake)
Fuel cut is set to 7000 rpm due to the stock rotating assembly. Needless to say I am very pleased with the numbers based upon the relatively mild cams and low 7000 RPM redline. It is still increasing power at fuel cut. I will try and post the dyno chart in the next couple days.
-I will be testing this modified intake manifold within the next couple weeks. I think it will show definitively whether it is a winner. C8 cams, PPE headers, Large intake, your upper intake, ported rev up lower and ported lower intake manifold, UP rev tuning, and full exhaust with no restriction. Revving to 7000 rpm...lets see how this goes!!
Thank you for coming up with this design...I am excitement to see some results!
Fast forward to April 2017. My car with a new rebuilt engine has put 331 WHP down on a Mustang dyno.
On to the pieced together stock-ish VQ35DE...
-Rebuilt engine
-Stock bottom end from a REV UP (Pistons, rods, block, crankshaft)
-Stock Non-Revup Heads
-Upgraded ARP Rod Bolts
-New Bearings
-New rings, etc...
-Revup Oil Pump
-PPE Longtube headers
-Single 3 " Agency Power Exhaust
-JWT C8 Cams and Springs
with stock throttle body, upper intake manifold, *ported revup lower, and Momentum intake and UPREV dyno tuning...
-331 WHP on a Mustang Dyno!! (Without this modified upper intake)
Fuel cut is set to 7000 rpm due to the stock rotating assembly. Needless to say I am very pleased with the numbers based upon the relatively mild cams and low 7000 RPM redline. It is still increasing power at fuel cut. I will try and post the dyno chart in the next couple days.
-I will be testing this modified intake manifold within the next couple weeks. I think it will show definitively whether it is a winner. C8 cams, PPE headers, Large intake, your upper intake, ported rev up lower and ported lower intake manifold, UP rev tuning, and full exhaust with no restriction. Revving to 7000 rpm...lets see how this goes!!
Thank you for coming up with this design...I am excitement to see some results!
#172
New Member
That intake pipe is way too long & too many transition pieces cocky. I did something similar after having a shorty 4" pipe that worked very well. I added an extension, along with a 45* bend to get the filter out of the bay & it killed my 0-60 time by 1 full second. Put it back the way it was, actually shortened it up 5" and built an air box around it.
Last edited by onevq35de; 12-26-2017 at 07:49 PM.
#173
Thread
Thread Starter
Forum
Replies
Last Post