VQ35HR 2007 350z Zex Nitrous Kit Install Started
I am filming and working on the car, so it is going slower then it should. If I could work straight through on this kit, it would take about 5-6 hours to completely do.
Today I installed everything under the engine bay, including part of my purge kit, as well as new intakes. What is left is wiring, finish the purge, and mount the bottle. I will finish it up next week. Here are some of my initial shots I will be putting together an install video, including dyno runs after it is completed, so stay tuned You cannot remove the line off the regulator on 350zs. If you follow it to the bottom corner, you will see a quick disconnect. That and the blue clip is removed and transferred to the fitting that comes with the zex kit, as well as a new quick disconnect that goes on the other side of the adaptor to your fuel line. Nozzles are mounted underneath the pipe about 2 inches past the MAF The nitrous and fuel are T-ed for the twin intakes, behind the intake manifold and infront of the Zex box. The box is also mounted upside down so I could run the lines better. It isnt cleaned up yet since I still have work to do. http://www.floridaracing.org/z/zex/IMG_6348.JPG http://www.floridaracing.org/z/zex/IMG_6351.JPG http://www.floridaracing.org/z/zex/IMG_6353.JPG http://www.floridaracing.org/z/zex/IMG_6356.JPG http://www.floridaracing.org/z/zex/IMG_6357.JPG http://www.floridaracing.org/z/zex/IMG_6358.JPG http://www.floridaracing.org/z/zex/IMG_6360.JPG http://www.floridaracing.org/z/zex/IMG_6361.JPG |
Originally Posted by powermark
(Post 6748080)
I am filming and working on the car, so it is going slower then it should. If I could work straight through on this kit, it would take about 5-6 hours to completely do.
Today I installed everything under the engine bay, including part of my purge kit, as well as new intakes. What is left is wiring, finish the purge, and mount the bottle. I will finish it up next week. Here are some of my initial shots I will be putting together an install video, including dyno runs after it is completed, so stay tuned You cannot remove the line off the regulator on 350zs. If you follow it to the bottom corner, you will see a quick disconnect. That and the blue clip is removed and transferred to the fitting that comes with the zex kit, as well as a new quick disconnect that goes on the other side of the adaptor to your fuel line. Nozzles are mounted underneath the pipe about 2 inches past the MAF The nitrous and fuel are T-ed for the twin intakes, behind the intake manifold and infront of the Zex box. The box is also mounted upside down so I could run the lines better. It isnt cleaned up yet since I still have work to do. http://www.floridaracing.org/z/zex/IMG_6348.JPG http://www.floridaracing.org/z/zex/IMG_6351.JPG http://www.floridaracing.org/z/zex/IMG_6353.JPG http://www.floridaracing.org/z/zex/IMG_6356.JPG http://www.floridaracing.org/z/zex/IMG_6357.JPG http://www.floridaracing.org/z/zex/IMG_6358.JPG http://www.floridaracing.org/z/zex/IMG_6360.JPG http://www.floridaracing.org/z/zex/IMG_6361.JPG |
Wow, please don't quote all the pics.
OP, thanks for the video install. Your work looks good so far. |
Nice job. Looking forward to see how it runs.
|
yes finally
|
Any updates?
|
Been slammed out of my mind, hope to have running in the next 2-3 weeks.
|
Pleases could someone please explain the factory "quick fuel disconnect" I'm trying to get everything figured out and located before I start my tear down
|
All times are GMT -8. The time now is 03:06 PM. |
© 2024 MH Sub I, LLC dba Internet Brands