MY350Z.COM - Nissan 350Z and 370Z Forum Discussion - Search Results

Notices
 
Search: Posts Made By: MR RIZK
Showing results 1 to 30 of 461
Search took 0.33 seconds.
10-07-2014, 11:24 PM
Replies: 119
Views: 22,370
Posted By MR RIZK

Row2k as a consumer I understand where you are...

Row2k as a consumer I understand where you are coming from however these items are marketed at the track/high performance street setups and as such they are not going to have the same level of...
10-07-2014, 10:20 PM
Replies: 69
Views: 63,538
Posted By MR RIZK

Listed on this site. Not sure if correct but...

Listed on this site. Not sure if correct but maybe a starting point

http://injector-rehab.com/shop/lag.html
08-01-2014, 06:05 AM
Replies: 62
Views: 10,863
Posted By MR RIZK

If the 60mm fit why wouldn't the 52's? Anyway...

If the 60mm fit why wouldn't the 52's? Anyway shamless plug, if you are after a set of defi gauges complete that have been modified to fit let me know as my set are for sale.

See picture in...
04-03-2014, 03:29 AM
Replies: 88
Views: 31,232
Posted By MR RIZK

the piston is stepped. The metal ring the boot is...

the piston is stepped. The metal ring the boot is affixed to is what the top hat sits on. take the spring off and you will notice it will not slide up and down the piston as it sits on the bump stop...
04-03-2014, 02:34 AM
Replies: 88
Views: 31,232
Posted By MR RIZK

1. take the top adjuster knob off 2. take off...

1. take the top adjuster knob off
2. take off the 2 nuts under the adjuster
3. take off the 2 nuts above the boot
4. reuse your oem upper top hat
5. use the nuts from point 3 to secure the oem...
Forum: Engine
03-25-2014, 05:44 PM
Replies: 3
Views: 729
Posted By MR RIZK

Stock block Single HKS GT3037 turbo kit Power...

Stock block
Single HKS GT3037 turbo kit
Power Enterprise 510cc injectors
Around 7psi of boost
Forum: Engine
03-25-2014, 04:12 PM
Replies: 3
Views: 729
Posted By MR RIZK

Open to offers

Open to offers
Forum: Engine
01-26-2014, 10:43 PM
Replies: 3
Views: 729
Posted By MR RIZK

HKS FCON V Pro + new Harness

For sale is a used HKS F-CON V PRO and a brand new harness. The ecu is a RED dot and running 3.24 firmware. Still has my map in the ecu when my car was boosted. The harness is to suit a 350z and has...
09-14-2013, 12:33 AM
Replies: 10
Views: 1,697
Posted By MR RIZK

New tech is always cool, however it is like 3-way...

New tech is always cool, however it is like 3-way adjustable dampers. Most owners are unable to dial in 1-ways most of the time.
Forum: Brakes
08-30-2013, 05:29 PM
Replies: 3
Views: 1,454
Posted By MR RIZK

As per Waizzz request see below for additional...

As per Waizzz request see below for additional photos of the item.

Boxes
http://imageshack.us/a/img834/2271/hr35.jpg

Rear Caliper
http://imageshack.us/a/img692/1603/hajh.jpg

Pads...
Forum: Brakes
08-29-2013, 04:42 AM
Replies: 3
Views: 1,454
Posted By MR RIZK

Stoptech Trophy Sport 6/4 Pot BBK - BNIB

Here is a rare opportunity to purchase a brand new set of Stoptech Trophy Sport BBK to suit the 2003+ nissan 350z. These are light weight components compared to other BBK's on the market. Items are...
Forum: Tuning
08-12-2013, 05:03 PM
Replies: 18
Views: 3,151
Posted By MR RIZK

@str8dum1 What does your miss counter report...

@str8dum1

What does your miss counter report during crank? I found that when i replaced the bank 1 sensor with a new one it was too close and the car didn't start. Took me a while to find a...
Forum: Tuning
08-11-2013, 06:06 AM
Replies: 18
Views: 3,151
Posted By MR RIZK

lol.. looks like the BRZ has the same issue. Fix...

lol.. looks like the BRZ has the same issue. Fix according to Subaru TSB is to shim the sensor.

http://www.ft86club.com/forums/attachment.php?attachmentid=46296&stc=1&d=1375302652
08-01-2013, 05:07 PM
Replies: 24
Views: 9,264
Posted By MR RIZK

f$%k that was quick. I got the seal out with the...

f$%k that was quick. I got the seal out with the upper oil pan in but no way in hell i could get it back in with the half moon seal. Some have and kudus to them.

Least you know what the issue is. ...
07-31-2013, 02:14 PM
Replies: 24
Views: 9,264
Posted By MR RIZK

If you push the seal on straight when it is on...

If you push the seal on straight when it is on the stand it will lip. When I rebuilt my engine i had a rear main seal leak. Got to a point where it was a steady stream of oil. After I removed the...
07-31-2013, 02:15 AM
Replies: 12
Views: 1,211
Posted By MR RIZK

BMW M models use 10w60 Castrol TWS as a...

BMW M models use 10w60 Castrol TWS as a comparison.
07-31-2013, 01:43 AM
Replies: 24
Views: 9,264
Posted By MR RIZK

Search this forum in regards to the rear main...

Search this forum in regards to the rear main replacement. There are some tricks in putting them in without lipping the seal or dropping the engine again.
07-11-2013, 03:02 PM
Replies: 6
Views: 905
Posted By MR RIZK

hmm.. I get you now and the copper pipe to...

hmm.. I get you now and the copper pipe to dissipate the heat before the gauge. That's going to be a pain to test :)
07-11-2013, 03:32 AM
Replies: 6
Views: 905
Posted By MR RIZK

@racer59, Do you mean a typical exhaust back...

@racer59, Do you mean a typical exhaust back pressure test. ie: plumb tester into upstream O2 port and rev to 3000rpm?

Base timing is about 14 degrees and VCC is about 10 > 6 degrees in that rpm...
07-10-2013, 12:10 AM
Replies: 6
Views: 905
Posted By MR RIZK

not really. I'm trying to find out if the comp...

not really. I'm trying to find out if the comp side of the 76r is the same as the HKS unit. Both have a comp 60 A/R but with our setup there is less than 2mm clearance to the starter motor. Any...
06-27-2013, 05:56 AM
Replies: 5
Views: 983
Posted By MR RIZK

figures that were listed on the forum ages ago ...

figures that were listed on the forum ages ago

90-95 ft/lbs for the L19
60-65 ft/lbs for the ARP Mains
06-21-2013, 11:29 PM
Replies: 6
Views: 905
Posted By MR RIZK

HKS ST Replacement turbo advice

Below is a recent dyno graph on my car. As you can see power starts to drop off between 5-7k rpm since I have increased the boost. The scaling of the graph makes it look worse. The car is currently...
06-21-2013, 09:17 PM
Replies: 201
Views: 22,250
Posted By MR RIZK

Good to see you are still developing on the...

Good to see you are still developing on the platform.. keep it up and looking good
06-19-2013, 06:46 AM
Replies: 33
Views: 2,084
Posted By MR RIZK

The leak was on the lower collector. I had a...

The leak was on the lower collector. I had a Cosworth phenolic intake manifold spacer and the sealant was leaking. I replaced with OE gasket and this fixed the leaks.
06-18-2013, 11:21 PM
Replies: 33
Views: 2,084
Posted By MR RIZK

Quick update. As above I fixed the vac leaks and...

Quick update. As above I fixed the vac leaks and also installed the original IC. The reason I installed the smaller IC is because I was chasing issues with power at top end which I don't believe I...
06-17-2013, 04:03 AM
Replies: 33
Views: 2,084
Posted By MR RIZK

All, Thanks for feedback. I fixed my vac leak...

All, Thanks for feedback. I fixed my vac leak issues and I know most of you said that it probably wont make a difference but it can't hurt to test. Hopefully I can get it back on the dyno soon to see...
06-11-2013, 05:48 PM
Replies: 33
Views: 2,084
Posted By MR RIZK

Jeff, I thought that the pressure should be base...

Jeff, I thought that the pressure should be base pressure + map at that point in time.

I have emailed DW also but not holding my breath.
06-11-2013, 04:50 AM
Replies: 33
Views: 2,084
Posted By MR RIZK

I have a fuel pressure sensor plumped into the...

I have a fuel pressure sensor plumped into the FPR and then hooked into one of the haltech inputs of their PNP unit.

@str8dum1, You will notice in the graph it is nearly rising 1:1 between 2k and...
06-09-2013, 10:01 PM
Replies: 4
Views: 1,162
Posted By MR RIZK

If all the PID and CLBD settings are ok try...

If all the PID and CLBD settings are ok try increasing the control start pressure or increasing the closed loop delay. If the delay is too short once the boost builds as per the CLBD table and hasn't...
06-09-2013, 06:49 PM
Replies: 33
Views: 2,084
Posted By MR RIZK

I will need to look into that. I don't have any...

I will need to look into that. I don't have any of the lean spot issues that others have faced with a RFS. If I go down the hard-line upgrade I need to work out options to retain the fuel damper on...
Showing results 1 to 30 of 461
 


 
Forum Jump

Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.