[DFW]: DFW's Lounge
#8901
Living in 350Z
iTrader: (64)
Prob thursday, i heard you coming over on friday. I will be there on saturday to doing what i can do over there. I have to get myself ready to delete my tune. It will be fun
Oh i gave him your gasket that goes between TB and plenum.
Edit: also wheel buyer is coming from houston this saturday...god...everything is gone really fast....
Oh i gave him your gasket that goes between TB and plenum.
Edit: also wheel buyer is coming from houston this saturday...god...everything is gone really fast....
Of course everything is going quick dude..
Mad REP + Fast Car + good deals = Stuff SOLD FAST..
Props Chef..I hope whatever your doing this for gets handled and taken care of, and then some..
#8908
I am Awesome
iTrader: (4)
It was our friend
He does great work and I will continue to use and refer him, he has done this install and so many other installs before so I doubt it was something he did.
Its just we installed the alarm and changed out the stereo at the same time. He was doing the alarm and Tommy and I were doing the stereo so something between those two caused this to happen.
I don’t think it is anything big just something small, we just didn’t have anything to read the codes to even know where to start.
But all is good now that we have the reader – Thanks Jake
He does great work and I will continue to use and refer him, he has done this install and so many other installs before so I doubt it was something he did.
Its just we installed the alarm and changed out the stereo at the same time. He was doing the alarm and Tommy and I were doing the stereo so something between those two caused this to happen.
I don’t think it is anything big just something small, we just didn’t have anything to read the codes to even know where to start.
But all is good now that we have the reader – Thanks Jake
#8911
Registered User
Join Date: Jan 2007
Location: Dallas
Posts: 174
Likes: 0
Received 0 Likes
on
0 Posts
this might be a coincidence but yesterday we had an alarm installed on kristi's car. Everything was fine until we were about to leave. The Service Engine Soon, TCS OFF, and SLIP lights are all on and you can floor the gas pedal and the car will barely go.
When you start the car the rpms drops and the car dies or rpm drops and it has a rough recovery to idle or you give it a little gas when starting and it will idle
I have pulled the battery for 6 hours and tried again and the lights are still there. I even tried the manual ECU reset by turning key on and hitting gas pedal but nothing.
ANYONE?? I have not pulled codes yet.
When you start the car the rpms drops and the car dies or rpm drops and it has a rough recovery to idle or you give it a little gas when starting and it will idle
I have pulled the battery for 6 hours and tried again and the lights are still there. I even tried the manual ECU reset by turning key on and hitting gas pedal but nothing.
ANYONE?? I have not pulled codes yet.
I was driving on the highway and when I clutched in to change gears, the rpm dropped and I stalled out, took forever to get it started again but once it did, it would spaz out and go in and out of limp mode, all the lights were on too. Early Zs are known to have this problem, check if you are still able to get it serviced at a Nissan dealership, there was a TSB released for it.
For the second symptom, when I got my car back from Sterling, I had the issue of where my car would die after starting it up. Only happened when the car was warmed up. If it was a cold start, it would start up fine. It would start up fine too if I blip the throttle a little bit. I have unhooked the battery and swapped out the MAF sensor. Turns out Sterling have unhooked the battery for quite some time and I had to do the procedure of relearning the idle. If you do a quick google search, you should be able to find the procedure.
Last edited by drifter5; 09-15-2009 at 10:50 AM.
#8915
Registered User
#8919
Booooosstt!!
iTrader: (58)
Join Date: Mar 2007
Location: Dallas/NewYork/Michigan/Korea
Posts: 5,311
Likes: 0
Received 0 Likes
on
0 Posts
It will hit 400whp on mustang dyno or close to it. But i will say weaksauce tuner...I really want him to go with osiris...but we will see how it turn out. There is no need wire, expect gauges.
Last edited by Chef-J; 09-15-2009 at 04:46 PM.