XXR Wheels Thread
07-11-2012, 05:34 PM
#944
Registered User
Join Date: Jun 2012
Location: Melbourne, Florida
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
word; so you're running the +20 wheels with 25mm spacers front and rear? any fender rolling going on for that setup? I'm about to do the same on NF210's
07-11-2012, 05:57 PM
#945
Registered User
iTrader: (1)
Join Date: Oct 2009
Location: Sacramento
Posts: 404
Likes: 0
Received 0 Likes
on
0 Posts
07-11-2012, 08:48 PM
#947
Registered User
Join Date: Jun 2012
Location: Melbourne, Florida
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Oh true. im runnin 18X8.75's w 245/45 on the rear. Probably wont have to pull the fenders, just roll em. Thats a wide wheel you're runnin..
07-14-2012, 12:51 PM
#949
XXR 526 and Brembos
A friend asked me if these would fit her car in a 18 x 10.5 rear with Brembos on rear wth 275-40-18s and 18 x 8.5 with 245-40+182 on front. Mostly concerned with fitment of these over the brembos and rubbing in the rear.
Will they work?
Will they work?
07-14-2012, 04:25 PM
#957
Post i found from another thread
____________
TCS Function
The wheel spin occurrence of the drive wheels is detected by the ABS actuator and electric unit (control
unit) using the wheel speed signals from all four wheels, so when wheel spin occurs, the amount of wheel
spin is reduced by controlling the hydraulic brakes on the right and left rear wheels, cutting the fuel to the
engine, and partially closing the throttle valve to reduce the engine torque. The throttle opening is also
controlled to obtain the optimum engine torque.
Depending on road circumstances, the driver may have a sluggish feel. This is normal, because the optimum
traction has the highest priority under TCS operation.
TCS may be activated any time the vehicle suddenly accelerates, suddenly downshifts, or is driven on a
road with a varying surface friction coefficient.
During TCS operation, it informs a driver of system operation by flashing SLIP indicator lamp.
VDC Function
In addition to the TCS/ABS function, the driver steering amount and brake operation amount are detected
from the steering angle sensor and pressure sensor, and the vehicle's driving status (amount of understeering
/ over-steering) is determined from information from the yaw rate sensor/side G sensor, wheel
sensor, etc., and this information is used to improve vehicle stability by controlling the braking and engine
power to all four wheels.
The SLIP indicator lamp flashes to inform the driver of VDC operation.
During VDC operation, the body and brake pedal lightly vibrate and mechanical noises may be heard.
This is normal.
The ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp might turn on when the vehicle
is subject to strong shaking or large vibration, such as when the vehicle is on a turn table or a ship while
the engine is running. In this case, restart the engine on a normal road, and if the ABS warning lamp, VDC
OFF indicator lamp, and SLIP indicator lamp turn off, there is no problem.
____________
TCS Function
The wheel spin occurrence of the drive wheels is detected by the ABS actuator and electric unit (control
unit) using the wheel speed signals from all four wheels, so when wheel spin occurs, the amount of wheel
spin is reduced by controlling the hydraulic brakes on the right and left rear wheels, cutting the fuel to the
engine, and partially closing the throttle valve to reduce the engine torque. The throttle opening is also
controlled to obtain the optimum engine torque.
Depending on road circumstances, the driver may have a sluggish feel. This is normal, because the optimum
traction has the highest priority under TCS operation.
TCS may be activated any time the vehicle suddenly accelerates, suddenly downshifts, or is driven on a
road with a varying surface friction coefficient.
During TCS operation, it informs a driver of system operation by flashing SLIP indicator lamp.
VDC Function
In addition to the TCS/ABS function, the driver steering amount and brake operation amount are detected
from the steering angle sensor and pressure sensor, and the vehicle's driving status (amount of understeering
/ over-steering) is determined from information from the yaw rate sensor/side G sensor, wheel
sensor, etc., and this information is used to improve vehicle stability by controlling the braking and engine
power to all four wheels.
The SLIP indicator lamp flashes to inform the driver of VDC operation.
During VDC operation, the body and brake pedal lightly vibrate and mechanical noises may be heard.
This is normal.
The ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp might turn on when the vehicle
is subject to strong shaking or large vibration, such as when the vehicle is on a turn table or a ship while
the engine is running. In this case, restart the engine on a normal road, and if the ABS warning lamp, VDC
OFF indicator lamp, and SLIP indicator lamp turn off, there is no problem.
Last edited by Bmurray350z; 07-14-2012 at 04:27 PM.
The following users liked this post:
resident25 (08-25-2015)
