I can see this being a concern if your buying pays like engine internals or suspension but how could they screw up shipping a seat. Normally I wouldn't look abroad as I like to support the local economy but at 50% off its hard to resist.
|
Didn't look, but you sure the stuff isn't just left-over, out of date safety equipment?
|
The poles are very good at doing things in a not legitimate fashion. It would not be unheard of to have switched tags showing current dates on older stock...
|
Originally Posted by armt350z
(Post 10687947)
The poles are very good at doing things in a not legitimate fashion. It would not be unheard of to have switched tags showing current dates on older stock...
If I wait till January do i get a 2016 label sticker which would make it good till 2021? Also I have very little insight on seat mounts... are you guys running custom mounts or buying those L brackets from sparco/recaro? |
I'm running a planted driver side and a hacked up and welded planted passenger side
|
Cool thx.
|
https://cimg8.ibsrv.net/gimg/my350z....efb7ce25dc.jpg
By https://cimg9.ibsrv.net/gimg/my350z....4ef8bcbb2b.jpg https://cimg3.ibsrv.net/gimg/my350z....1a8f403dc7.jpg Harness cleaned up... didn't have time to go after sound deadening. |
https://cimg5.ibsrv.net/gimg/my350z....e345be9eb8.jpg
This stuff is more stubborn than I thought... stuff under seats is going to be PITA |
Dry Ice?
|
Originally Posted by 03threefiftyz
(Post 10688458)
Dry Ice?
Used a small gasket scraper and hammer... wire wheel to clean it up. |
Looks about the same with dry ice...let it sit, smack it with a hammer. Get those nice chunks all the same.
|
Originally Posted by 03threefiftyz
(Post 10688815)
Looks about the same with dry ice...let it sit, smack it with a hammer. Get those nice chunks all the same.
|
Originally Posted by terrasmak
(Post 10688904)
He could live in a cold area
Live in Michigan and was mid 40s yesterday. |
|
https://cimg6.ibsrv.net/gimg/my350z....830065c3af.jpg
https://cimg9.ibsrv.net/gimg/my350z....18a33e4bbe.jpg Cleaned up, gotta hit it with some paint. |
Are you guys running keyless ignition? Anyone have a schematic of how to wire up keyless? Also any schematics on emergency cutoff switch?
|
https://cimg4.ibsrv.net/gimg/my350z....ce2499756c.jpg
Inside is done, waiting on seat to come in... then it goes for cage. Not quite sure what to do with the open ends of the heater core lines... the outlet part looks like it goes into the head do I'm not sure if it's ok just to block it off... any input? https://cimg9.ibsrv.net/gimg/my350z....3d550c580f.jpg Outlet goes here https://cimg0.ibsrv.net/gimg/my350z....2f93cb85ff.jpg Outket line terminates to hard line https://cimg1.ibsrv.net/gimg/my350z....66487e44cc.jpg This was where the inlet line came from. |
possibly just plumb a loop from outlet to inlet. The LS guys have been doing that for ages.
|
Originally Posted by armt350z
(Post 10691029)
possibly just plumb a loop from outlet to inlet. The LS guys have been doing that for ages.
I was thinking that but I'd like to eliminate the line if it is unnecessary. I be my eve people have removed it so I'm wondering how they did it. |
On my LS you have to loop it. If you block it, the motor overheats. But then again its like 3 inches of hose and 2 hose clamps.
|
All times are GMT -8. The time now is 11:08 PM. |
© 2024 MH Sub I, LLC dba Internet Brands