MY350Z.COM - Nissan 350Z and 370Z Forum Discussion
0 2026/05/21 17:06:32
0 2026/05/21 17:06:31
0 2026/05/21 17:06:30
0 2026/05/21 17:06:29
0 2026/05/21 17:06:28
0 2025/10/28 16:40:58
0 2025/10/27 21:40:10
0 2025/10/27 21:39:30
Starting system circuit logic (sequence).
Starting system circuit logic (sequence).
0 2025/05/15 22:39:50
End of starter wiring.
End of starter wiring.
0 2025/05/15 22:39:48
Beginning of starter wiring.
Beginning of starter wiring.
0 2025/05/15 22:39:44
Troubleshooting steps.
Troubleshooting steps.
0 2025/05/15 22:39:42
0 2025/04/09 13:43:34
Zspeed tray in place, slightly elevated angle. Notice the hatch bolts.
Zspeed tray in place, slightly elevated angle. Notice the hatch bolts.
0 2025/03/03 22:49:17
Side view with Zspeed Undertray. Right around 10mm of clearance.
Side view with Zspeed Undertray. Right around 10mm of clearance.
0 2025/03/03 22:49:14
Driver side view.
Driver side view.
0 2025/03/03 22:44:05
Passenger side view.
Passenger side view.
0 2025/03/03 22:44:02
Installed, waiting for it to cure. Oil filter was drained. I re-installed to keep from getting dripped on.
Installed, waiting for it to cure. Oil filter was drained. I re-installed to keep from getting dripped on.
0 2025/03/03 22:43:58
Full kit, unboxed, as it comes from Z1.
Full kit, unboxed, as it comes from Z1.
0 2025/03/03 22:43:56
Inside view of inner and outer casing.
Inside view of inner and outer casing.
0 2024/10/01 00:26:55
All parts cleaned up. New replacement parts also shown.
All parts cleaned up. New replacement parts also shown.
0 2024/10/01 00:26:42
Screws circled in yellow.
Screws circled in yellow.
0 2024/10/01 00:24:01
Bearing removed, I needed to add a longer socket/bit to get the last few mm of the bearing off.
Bearing removed, I needed to add a longer socket/bit to get the last few mm of the bearing off.
0 2024/10/01 00:12:11
Home-brew bearing puller. Just a cheap Harbor Freight ball joint separator. Works great!
Home-brew bearing puller. Just a cheap Harbor Freight ball joint separator. Works great!
0 2024/10/01 00:12:09
0 2024/10/01 00:04:25
0 2024/10/01 00:04:23
Casing separated, rotor with front case. Note: I removed the pulley 1st, but the rust kept the rotor with the front casing during separation.
Casing separated, rotor with front case. Note: I removed the pulley 1st, but the rust kept the rotor with the front casing during separation.
0 2024/10/01 00:04:21
Side view
Side view
0 2024/10/01 00:03:12
Rear View
Rear View
0 2024/10/01 00:03:10
Front View - Notice 4x8mm perimeter bolts
Front View - Notice 4x8mm perimeter bolts
0 2024/10/01 00:03:08
0 2024/09/10 17:37:01
0 2024/08/12 21:32:42
The Axxess ASWC-1 brainbox and main wiring.
The Axxess ASWC-1 brainbox and main wiring.
0 2024/08/12 21:30:50
3.5mm jack from Axxess to Kenwood.
3.5mm jack from Axxess to Kenwood.
0 2024/08/12 21:30:49
SWC Posi-taps on factory harness
SWC Posi-taps on factory harness
0 2024/08/12 21:30:46
Head Unit - Wiring test.
Head Unit - Wiring test.
0 2024/08/12 21:29:41
0 2024/07/12 20:01:12
My mistake in pure Landau Black. Notice the wrinkles?
My mistake in pure Landau Black. Notice the wrinkles?
0 2024/07/01 23:47:04
Original on left. Pure Landau Black on right
Original on left. Pure Landau Black on right
0 2024/07/01 23:46:59
Original paint on left. SEM blend match on right.
Original paint on left. SEM blend match on right.
0 2024/07/01 23:46:54