Almost finished the fuel pump/ sending unit. I was lucky enough to find a used one locally for a good price as one of my spring holders is broken. Just gotta tighten the bottom hose clamp, solder and heat shrink the wires and add a hose clamp to hold the pump in place.
The pump is a walbro 450 if anyone was wondering. Hoping to get the fuel lines ran to the engine bay this weekend and hoping to install the motor Tuesday or Wednesday. https://cimg4.ibsrv.net/gimg/my350z....7809352037.jpghttps://cimg6.ibsrv.net/gimg/my350z....9a2488f703.jpg |
Chase bays power steering line installed
https://cimg2.ibsrv.net/gimg/my350z....4780a57605.jpg https://cimg4.ibsrv.net/gimg/my350z....de28ba35b7.jpg https://cimg6.ibsrv.net/gimg/my350z....7dd9e60a53.jpg |
Looking good Ragg!
|
So after lots of swearing I could get the fuel assembly to go into the tank. I am so high on gas fumes.
I figured out why the last fuel tank hanger was broken, the tank was bent upwards which caused the spring mechanism to snap. So I pounded the tank out with a 2x4 and a sledge hammer and now its straightened out and fits....but the damn gas fumes had me going crazy haha https://cimg2.ibsrv.net/gimg/my350z....1b021f1441.jpg |
I have to run the fuel lines, install the new clutch line and a few more things tomorrow, then Monday or Tuesday (Weather dependant) I will be installing the motor/harness
|
The fuel lines are in hardest part was getting them to fit around the fuel tank took a bit of prying with a pry bar.
I only ran the lines half way waiting for engine to be in to find the final position. The run up right next to the manifold / Down pipe which is concerning https://cimg5.ibsrv.net/gimg/my350z....0db17632c1.jpg |
Originally Posted by Raggan
(Post 11002269)
The run up right next to the manifold / Down pipe which is concerning
|
Originally Posted by bealljk
(Post 11002290)
Aeroquip fire sleeve
|
Well I bit of a hick up, I was flustered today and didn't read the torque specs on the clutch pressure plate.....bolt snapped in the flywheel.
Damn I really gotta pay more attention, it's gonna cost me a few $ to get it extracted at the machine shop. Also I am now wondering about the stock, 350z clutch fork doesn't seem to be locking into place on the pivot ball. It seems to lift off the ball when i press on the clutch fork, maybe I should order the upgraded one and just wait a few weeks? |
Taking a break away from the car for a bit, Need to order the 2006 350z clutch fork and pivot ball.
Currently I have the 2003 fork/pivot ball, which is too weak for the ACT stage 5 clutch. Flywheel is ready to be picked up at the machine shop. I am just waiting till payday to order a clutch fork/pivot ball, funds are tight atm, because of the turbo payments. I gotta slow down I was rushing things too much. It's not like I can drive it, when it's done as it wont be driven in the winter anyways. |
You'll get there
Do you have a clutch alignment tool? |
Originally Posted by bealljk
(Post 11002587)
You'll get there
Do you have a clutch alignment tool? Yes the collins kit supplied the clutch alignment tool. |
Originally Posted by Raggan
(Post 11002596)
Yes the collins kit supplied the clutch alignment tool.
one step at a time and make progress each day / each week / each month ... if nothing more, fail-forward |
Made some progress today
Picked up the flywheel at the machine shop Ordered a 2006 clutch fork assembly from Nissan, should be here Tuesday Starter, clutch/flywheel, intake, cam cover installed. https://cimg3.ibsrv.net/gimg/my350z....b0c506d3c9.jpg https://cimg5.ibsrv.net/gimg/my350z....27b016e82a.jpg https://cimg8.ibsrv.net/gimg/my350z....eb00200557.jpg https://cimg9.ibsrv.net/gimg/my350z....2701e3f6c5.jpg https://cimg2.ibsrv.net/gimg/my350z....dbacc8a2ad.jpg https://cimg3.ibsrv.net/gimg/my350z....872b1db6f1.jpg https://cimg5.ibsrv.net/gimg/my350z....160cd52745.jpg |
Hoping I have enough clearance for the intake- near the strut tower here are some measurements if anyone can chime in
https://cimg1.ibsrv.net/gimg/my350z....27116974c4.jpg https://cimg6.ibsrv.net/gimg/my350z....e65929c684.jpg https://cimg7.ibsrv.net/gimg/my350z....8fdcac1a74.jpg https://cimg8.ibsrv.net/gimg/my350z....0e03006522.jpg https://cimg9.ibsrv.net/gimg/my350z....2abd8ff7ef.jpg https://cimg0.ibsrv.net/gimg/my350z....93c143d683.jpg https://cimg5.ibsrv.net/gimg/my350z....4f82635ce3.jpg |
So I got the clutch fork and pivot ball today, I didnt realize I needed a 2006 throw out bearing spring/clip.
So another delay, damn I'm getting s bit frustrated. Just when you think you can bolt the trans to the block you realize you missed something.... Anyways delayed until Thursday. https://cimg5.ibsrv.net/gimg/my350z....7285f8081f.jpg https://cimg9.ibsrv.net/gimg/my350z....0d325b31c6.jpg https://cimg1.ibsrv.net/gimg/my350z....f854f46810.jpg https://cimg4.ibsrv.net/gimg/my350z....7ffb930f5c.jpg |
Alright so I just ordered the next round of parts nothing crazy fancy but stuff that's needed
x20 ARP 200-8683 M10 x 1.25 for exhaust Manifold/Turbo Bosch 4.9 Wide band sensor for my AEM gauge 3 Big Toyota OEM oil filters Idle air check valve and grommet replacement Flex fuel mounting bracket Oil pan inspection hole cover 1JZ/2JZ OEM thermostat 1JZ/2JZ Power steering pump feed pipe(outlet for reservoir) |
Raggan - please please please put solid mounts in … it will be soooo worth it. I had some fabricated but the Z1 six-shooter will be perfect and will give you more space in that area.
|
Originally Posted by bealljk
(Post 11003218)
Raggan - please please please put solid mounts in … it will be soooo worth it. I had some fabricated but the Z1 six-shooter will be perfect and will give you more space in that area.
|
All times are GMT -8. The time now is 01:52 AM. |
© 2024 MH Sub I, LLC dba Internet Brands