Yeah, thanks for the pics, I should have said that earlier. Justin, I agree that it looks difficult to place the tips in the middle--the piping shouldnt be a problem but the actual physical tips might be a problem.

I hope this rear bumper can be molded. Awesome.

ravi

 

Justin
Not quite sure what you mean.
The exhaust will stick through the mesh at the back so holes will have to be cut into that.
By prep work I meant that to get the valance to fit right was not a hard job.
The Valance is very very close to the back box though.
I may yet opt to cut 10mm off the back of the Valance.
Dirty thing in this pic is the back box

 

can't wait until someone gets it from Erebuni to see if it's the same one or what....

 

Anyone have a date on when we can start ordering from erebuni and get our discount?

 

ok, once again, when i recieve the ok from erebuni we can start calling to order with the 20% discount. the list has been sent to erebunis promotional dept. & they are reviewing the list. once they call me i will state the rep thier at erebuni with his ext # who will be in charge of our club ordering. untill then we need to be patient. i appologize for them on the wait, im sure were not the only club trying to get a disacount from them.......

steve, i apologize for not being more specific with the picture i was asking you to take. basically the picture would be as if you were laying on the ground on your back with your head centered in the middle of the car looking up, directly under where the exhaust exits through the new back valence. this way i can see the exhaust configuration in relation to the rear valence. another expample would be if the car were on a lift, you would stand under the car looking up at the rear muffler. in your periferal you would see the muffler, the exhaust piping, the new rear valence & how the tips exit through the rear valence. this is what i would like to see. again i apologize for being so critical, youve done more than enough to help us out already!..... i was wanting to cut my tips off, re-route the exhaust piping & have the exhaust tips exiting in the center diffuser section of the rear valence, not the steel mesh area like most intend to do. this picture would show if this re-routing is even possible. i certianly dont expect you to lye on your back, you can merely hold the camera under the rear valence close to the ground & point the camera upwards, then shoot a couple pics in that general area. this way you can see wich one looks best to post here.....

thankyou greatly steve!!!

-justin

 

steve, if you PM me your email address i can send you a pic of what im talking about. i have a PS pic of the tips moved to the center diffuser section. basically the tips would be on each side of the 2 slats that hand down in the center of the new rear bumper cover instead of through the opening where the steel mesh is..........

thanx again for all your help!

-justin

 

Justin
pm sent to you.

Steve

 

email sent to you steve, thanx!!

-justin

 

Cay you please ps the rear into ppw?
Thx

 

also, is 20% off final?
What are the prices of each part we have after the gb special?

 

I know alot of people want the rear valence, and I do know that when I got a price on it a while back it was 380.$ with our 20% discount it should be 304. before shiping

 

Justin,

No apologies needed, in fact, we(the my350.club members) should thank you for organizing it. You kept us well informed throughout the entire process. Now the ball is in Erebuni's court so to speak; we have no control over the approval process.
---------------
This thread is very long(being 20+ pages), and I understand it's hard to backtrack information, but all info are there, a little extra search effort will help avoid lots of repeated information.
Rgd,
Mickey

 

Sirzalot, I didn't do the PS I had somone else do it for me, sorry....

Also if your name was not on the list I sent to erebuni I'm sorry, but you will not be able to get the club discount..............

-justin

 

mickey, thanx for understanding & thanx for the kind words. really its my pleasure to return somthing to the z community!

-justin

 

So the gb ended already....... so sad.

 

Bump for updates--btw, what would the cost be on average for painting/installing the rear apron?

ravi

 

Still waiting to hear from erebuni, I'm going to call today to see what I can find out.......

Sorry I can't reply on costs for painting & installing the rear valence, mabey somone else can.........

-justin

 

Will have an up date on progress later on today.

Steve

 

what about steve on pricing, how much do you charge, we could transfer it to dolllars and get an estimate

 

ok, i was just over looking at the uk site and steve has finished the install of the rear to his car. he has posted pics and thoughts of the install process (page 22-25)

http://350zuk.com/forums/index.php?s...ic=4789&st=360

sounds like this could $$$ to prep and install