Vertex 1/2 Lip Kit Installed
Thread Starter
Registered User
iTrader: (19)
Joined: Apr 2008
Posts: 2,697
Likes: 3
From: Dirty Jersey
Originally Posted by J_Dizzle
haha well i have alot of hook ups too. my dad owns two NAPA Auto Part stores. so i know my fair share of people, haha
not to mention them DEKA batts.
Registered User
Joined: Apr 2007
Posts: 164
Likes: 0
From: mcallen tx
wow, me likey. I like this vertex kit more everytime I see it and it's in my favorite color. I hope you can make, and update on this post,
and take pictures in the daytime, when the car is good to go. make a lil photoshoot.
and take pictures in the daytime, when the car is good to go. make a lil photoshoot.
Can you get me free paintjobs also?
Originally Posted by Dr. Venture
no. It's an auto repair shop, but i can do minor fender bender's. But its good to have connections. Couple cases of BEER got me a free paint job on the body kit. YAY!!!
And if Anyones in the nj Middlesex Co area, look me up if ya need some work done.
North Brunswick Foreign & Domestic.
And if Anyones in the nj Middlesex Co area, look me up if ya need some work done.
North Brunswick Foreign & Domestic.
Thread Starter
Registered User
iTrader: (19)
Joined: Apr 2008
Posts: 2,697
Likes: 3
From: Dirty Jersey
Thanks!
Yeah when its all complete i'll take the Z on a nice day somewhere tight to take some cool pix.
I bought the kit from Intense.
The roof Spoiler is Stillen.
Yeah when its all complete i'll take the Z on a nice day somewhere tight to take some cool pix.
I bought the kit from Intense.
The roof Spoiler is Stillen.
Registered User
Joined: Jul 2007
Posts: 3,491
Likes: 0
From: Brantford, Ontario
sorry just some noob questions..
1) any pics of how the sides are mounted on the door step area? you know where you open the door, clips?
2) the back bumper, how does it stick to the original body? I seen the bottom bracket you made but is there some sory of double sided tape?
the kit looks great
1) any pics of how the sides are mounted on the door step area? you know where you open the door, clips?
2) the back bumper, how does it stick to the original body? I seen the bottom bracket you made but is there some sory of double sided tape?
the kit looks great
Thread Starter
Registered User
iTrader: (19)
Joined: Apr 2008
Posts: 2,697
Likes: 3
From: Dirty Jersey
Originally Posted by Doba
sorry just some noob questions..
1) any pics of how the sides are mounted on the door step area? you know where you open the door, clips?
2) the back bumper, how does it stick to the original body? I seen the bottom bracket you made but is there some sory of double sided tape?
the kit looks great
1) any pics of how the sides are mounted on the door step area? you know where you open the door, clips?
2) the back bumper, how does it stick to the original body? I seen the bottom bracket you made but is there some sory of double sided tape?
the kit looks great
Directions were in Japanese, But i figured it out.
Side Skirts mount normal front and rear( in wheel well) with the original rear push pin clips, and in the front the screws. In the door area i had to drill 4 holes into the frame to put the provided screws in to hold it in place. The skirts had all the holes pre drilled so i just followed that set up. Was not hard at all, except for the hole and screw nearest the door hinges. Didn't give you enough room really but i managed.
The front and the rear lips have predrilled holes that you mount around the fender going into the wheel well area and you have to drill some holes into the front and rear bumper edges. In the front where the kits lip goes over the lip under the grill i used 4 stripes of the provided Dsided tape. about 3 inches in length. on the rear it grabbed so tight i wasn't even able to put tape, so i made the bracket to hold it in place and keep it sturdy. Front bracket was just extra support.
And Thanks!!
Last edited by Dr. Venture; May 14, 2008 at 04:21 AM.