1. They're 19's.
2. Rears are 9.5, Fronts are 8.5
3. I didn't have to lower the car. It was personal taste. I think it looks tons better lowered compared to the Z's I have seen with wheels and stock suspension.
4. What overlays would you like more information on?

 

Sexy ! What percent tint is that ?

 

ok wtf.. im getting the photobucket icon

 

StudyB,

Appreciate the answers. The reason I ask if it was lowered, b/c I read that some people have lowered with Milanos & some have not. IMHO I think your set-up is dead on! Best SB Z I've seen clean in quite some time!

Did you put the overlays on your self? Does it come pre-cut or will someone have to apply them for you? Plus how dark is the tint. Is it a film or is it a plastic cover? You know how GA is here with their new tint laws!

 

meh, i get the bandwidth exceeded photobucket icon as well =P

 

+1

 

Dump this thread! Broken!

 

arrgghh!!

::: photobucket - bandwidth exceeded:::


i want to see!! hopefully the pics will be back up soon...

 

make them smaller and upload to forum?

 

I hate the wheels. ( But you know I'm kidding SB )....Beautiful car man, and some nice photography as well. The Milanos are a classic wheel.

 

I'm about to upgrade the account later on today. Just give me a chance to get some work done first. Pics will be back up soon.

 

Sorry about that guys. Fixed!

 

I had overlays at one point in time. Then I got the taillights done by a guy in Texas. PM me if you want his information.

The overlays I used were from lamin-x.com. They were pre-cut and were very thick overlays. Being so thick made them a lot easier to apply than many others overlays that I've seen. It's a very DIY job and I did them in 15-30 minutes. Just make sure you have patience and try to get all the bubbles out you can. The little bubbles will bake out in the sun.

 

Cool. I just checked out their website. Did you just get the "Tailights" kit or do I need the F&R Turn singals kit as well?

 

I did the F&R turn signals kit. It covers the front yellow reflectors. I will say that I had a problem with those though. They left a little slice of that yellow uncovered and it became extremely noticable.

 

I was wondering if those we the smoke reflectors or the overlay tint. I'll probably get some smoke reflectors & do the rear ones with the tint.

Thanks for the feedback. Again, great looking car!

 

Here's my list of mods. I have it in my signature on other sites, but this site is stingy and I can't get all of it in there. Hahahaha....

2003 Enthusiast SB 6MT/19" Axis Milano Wheels/Eibach Pro Kit Springs/Hotchkis Sway Bars/JWT Popcharger/Carbon Fiber Engine Cover/Viper 650XV Alarm/ 2 JL Audio 10w3v2's/JL Audio Stealthbox/JL Audio 500.1 Amplifier/Grounding Kit/EvoStyle EvoVision Turn Signal Bulbs/Hawk HPS Pads/StopTech SS Lines/Motul DOT 4 Fluids/S2000 Shorty Antenna/Removed Rear Wiper/Fairlady Z Badge/Smoked Taillights By Toykilla/Lamin-x Smoked Corner Overlays/JDM Smoked Sidemarkers/20% Tint/Grille Strips/Courtesy Z Emblems

 

"3. I didn't have to lower the car. It was personal taste. I think it looks tons better lowered compared to the Z's I have seen with wheels and stock suspension"

SB, I see that you have Eibach springs. I'm a newbie & I hope you don't mind all the questions, but dont these springs lower the car? I guess I'm a bit confused by the above statement that you didnt have to lower the car.

Again, sorry for all the questions, but I'm still learning from everyones knowledge here. Appreciate your help!

 

I think you're reading it wrong....Try this...

3. I didn't have to lower the car, but I did because that's my personal taste.

Yes, the Eibachs lower the car by .8" in the front and 1.2" in the rear. Most people are still able to align after this, but I've heard of a few that can't. If you're one of the unlucky ones, you need to be prepared to spend the $400 on a camber kit to make the car not eat tires.

 

Love the wheels!!!!