Work Meister S1 3pc. ROLL CALL
05-12-2008, 03:23 PM
#101
Registered User
iTrader: (13)
Join Date: Aug 2003
Location: Florida
Posts: 2,576
Likes: 0
Received 0 Likes
on
0 Posts
19x9.5 with a +24 offset in the front and 19x11 with a +29 offset in the rear... Only problem is that I'll have to use a 5mm spacer in the rear due to the breaks...
Last edited by rich harris; 05-15-2008 at 08:52 PM.
<--Me
05-30-2008, 08:32 AM
#106
Banned
iTrader: (8)
Join Date: May 2008
Location: Las Vegas, NV
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
this thread deserves a +1...work meister S1s..mmmmmmmmmmmm
ive been dying to pick a set of these up for my s13
but im also thinking about selling the s13 and buying a Z lol
ive been dying to pick a set of these up for my s13
but im also thinking about selling the s13 and buying a Z lol
06-05-2008, 12:48 PM
#110
Registered User
iTrader: (20)
Join Date: May 2006
Location: Houston, TX & WPB, FL
Posts: 1,946
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rich harris
19x9.5 with a +24 offset in the front and 19x11 with a +29 offset in the rear... Only problem is that I'll have to use a 5mm spacer in the rear due to the breaks...
06-05-2008, 05:07 PM
#111
Registered User
iTrader: (13)
Join Date: Aug 2003
Location: Florida
Posts: 2,576
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by masterj26
Rich, any pics of them on the car. Always wondered what the Gold S1's would look like on LS
06-05-2008, 05:57 PM
#112
New Member
iTrader: (24)
Join Date: Feb 2006
Location: Newport News VA
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
S1 setup
19x9.5 +24F 19x10.5 +23R
BTW Rich Im going with a Wilwood BBK 6 pot front with a 13 inch rotor
and it looks like a close fit due to the rivets and the step lip. What size
rotor do you have ?
BTW Rich Im going with a Wilwood BBK 6 pot front with a 13 inch rotor
and it looks like a close fit due to the rivets and the step lip. What size
rotor do you have ?
06-09-2008, 10:15 AM
#114
Registered User
iTrader: (13)
Join Date: Aug 2003
Location: Florida
Posts: 2,576
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by NIZZMO
19x9.5 +24F 19x10.5 +23R
BTW Rich Im going with a Wilwood BBK 6 pot front with a 13 inch rotor
and it looks like a close fit due to the rivets and the step lip. What size
rotor do you have ?
BTW Rich Im going with a Wilwood BBK 6 pot front with a 13 inch rotor
and it looks like a close fit due to the rivets and the step lip. What size
rotor do you have ?
just kidding... anyways I think you should be fine I went with a 14" front rotor 6 pot break system no problems here my set up is 19x9.5 off set +23 ....Good Luck!!!! hope this helps
