I love that body style. Good luck with the build!

 

Robbie, which Z seats are they?

 

Cloth factory seats in black.

 

Hmm..i wonder wat that would look like
I’m sure they wouldn’t bolt right up but your offer would be greatly appreciated..Donating for a good cause!

 

sucks i cant see these pictures at work

 

LOL i cant either..let me see if i can repost them up..give me a sec here...........

 

We can always try. One is at Dave's and the other is in my garage...somewhere.

 

lol thanks you feel my pain

 

LOL somewhere? I'm deff down for trying. That b an interesting look and theyre newer and actual black seats. The ones in there now have a sportier look to them and doesnt sit too bad..but they are old and smell a lil funny..and theyre that weird gray cloth

 

you should get in your titan and come up here and pick up my RB 240


• Car
1993 Nissan 240SX SE Convertible
117000 Miles
No rust on body, a little in lower rocker panel
No tears in soft top(two little silicone repair spots can be seen in pictures)
No cracks in the dash board, just torn driver seat
Everything is stock on the body/suspension. Story is my friend purchased this 240 from an old man in upstate CT, drove it for 4k miles to make sure car was worth upgrading. Purchased swap from 240sx motoring and was forced to sell due to hard times. Now I am the owner and will be selling it, I am buttoning up the last parts of the car to make it perfect. I am finishing up the wiring on the swap over the next few weeks.(I am an EE and Car audio installer so be confident in wiring)
It has a clean Carfax and will provide the Vin if you contact me.
KBB Value: $3,500
• Parts installed:
-Stitch welded engine bay-$XXX
-McKinney blue motor mount set-$400
-240 5 speed driveshaft set-$200
5 speed pedal set -$XX
-RB20DET engine with RB20 Transmission-$1500
Stock turbo(no shaft play)
Stock RB20DET ecu
-Stage 4 6 puck SPEC clutch kit-$400
-Greddy Extreme Timing belt=$125
-OEM Nissan RB20DET master overhaul gasket set-$280
-OEM Nissan RB water pump-$140
-Front mount Intercooler-$800
Front mount intercooler pipe kit
-BOV-$XXX
-Full 3 inch custom downpipe-$400
-ARP headstuds-200
-HKS Headgasket-150
-Full 3 inch exhaust-$950
-Koyo dual row aluminum radiator-$350
-New Vibrant muffler(not installed)-$115.40
-Apexi high power air filter-$140

Spare Parts:
Spare RB20DET (100% good to go,was going to build for 500hp+)-$1000
Spare RB20DET turbo (needs rebuild kit)-$300

Total installed parts: $6150.40

Total installed parts with spare parts: $7450

Vehicle+installedparts+spare parts:$10950

• Delivery: I can deliver the car within 150 miles for about $150. You can also pick it up in CT.

Payment: I am looking for cash or trade for a daily driver vehicle! I understand I won’t get what I spent on the vehicle and I also am NOT going to put this car up for a ridiculous price like I have seen online. People who ask 10k+ for 240’s are ridiculous. I am asking $6000.00 OBO As it sits or trade for a daily driver. You are buying TWO RB20DET’s with a convertible 240sx with no rust! If you wish to add anything to the car at your expense you can let me know and I will install anything you request before you purchase it. Thank you very much

Contact:
E-mail: Khanster@gmail.com
Or Pm me on here.

 

I've seen 350Z seats in a S13 before. They had custom rails but the seats fit in the car nice and looked good. I thought about doing it but the head room is not enough for me (240sx's not good for tall people) I got to cut the hump out of the floor to get the seats where I want them. From what I read it was not too difficult to get to work.

 

Lol well i won't have that problem seeing is that I'm small and all Where'd you see this at? ..do you have any pictures of it by any chance? I think it'd look good..and different as well..but i deff have to clean out the interior

 

BAM!
http://forums.nicoclub.com/zerothread?id=243537
http://www.240sxforums.com/forums/be...seats-s13.html
says they sit 2-3 inches higher depending on how the rails are modified. I have GTR (R32) seats and they were a bolt in job they sit about an inch higher. S14 seats are a bolt in as well plus they are not any higher.

 

Did you and Jonflip come up to me at chic a couple weeks ago? I had no idea you guys were building a 240. Looks good so far!

Here is my car:

 

Nice car, but ugly ugly ugly wheels

 

lol thanks.

I was going for a VIP styled 240 so the wheels go perfect with what I was trying to accomplish. Besides Work Wheels USA sponsored me, so I got the wheels for a great price. So I cant complain

 

Yea, bboyoracle we first met you at the college park meet then at Chik meet. Hence the reason why we were eyeballin' your car so hard and asked to see under the hood was b/c we're doing this build. I don't care what they say about your wheels, I love your car and the wheels are perfect!

 

Going to be pulling the motor out this Sunday starting at around 10-11am. If anybody would like to come by and hang out and/or work on your own car, your more than welcome. We'll be at my job in Chantilly behind Curry's Auto Service.

Curry's Auto Service
4003-A Westfax Drive
Chantilly, VA. 20152

If your coming and you need special attention for directions, you can hit me up at 703-629-0292.

 

Oo that’s you!!! LOL yeah we’re usually always at chic filA and we saw you at the college park meet too. Yeah, we were just imagining what my 240 was goin to be like soon. Your car is beautiful…very well done

DAMN IT JONATHAN!! You beat me to posting the motor pull out on Sunday!!!!
Grrr
But yeah, all you guys are more than welcome to come thru.
It’s a big lot with lots of parking space.. we’re even thinkin about havin’ a little grillin’ action goin on

 

Bboyoracle...you have one of my favorite 240's ever. That car is beautiful man.