Nismo #0831
Thread Starter
Joined: Feb 2008
Posts: 5,134
Likes: 3
From: FT Leonard Wood, MO
Unfortunately I need to replace my windshield this week and my Kenwood is on the fritz (paid $1500 for that POS). I hate throwing money away! After that mess gonna replace my rear rotors/pads (already did the front).
Thread Starter
Joined: Feb 2008
Posts: 5,134
Likes: 3
From: FT Leonard Wood, MO
Thread Starter
Joined: Feb 2008
Posts: 5,134
Likes: 3
From: FT Leonard Wood, MO
Appointment on Friday to get the windshield replaced. $185 after install and taxes. 1 little rock chip spread in about 5 minutes. Now it covers 75% of my windshield 
So here's the story on the exoticspeed exhaust. As some might remember, I had the JIC single and loved it (at first).

The problem was that my wife HATED it and it had a horrible drone on the Hwy. Even for me it was pretty freakin bad! Being the car is my daily driver, I couldn't afford any down time so I needed an exhaust before I could sell the JIC but money was tight as well. So a buddy of mine from this site was looking for a single exit and offered a straight trade for the exoticspeed. He even helped me remove the JIC and install this one on the spot. So until I save for a new exhaust, this will have to do.
So here's the story on the exoticspeed exhaust. As some might remember, I had the JIC single and loved it (at first).

The problem was that my wife HATED it and it had a horrible drone on the Hwy. Even for me it was pretty freakin bad! Being the car is my daily driver, I couldn't afford any down time so I needed an exhaust before I could sell the JIC but money was tight as well. So a buddy of mine from this site was looking for a single exit and offered a straight trade for the exoticspeed. He even helped me remove the JIC and install this one on the spot. So until I save for a new exhaust, this will have to do.
Last edited by jerseystyle; May 10, 2011 at 08:58 AM.
Thread Starter
Joined: Feb 2008
Posts: 5,134
Likes: 3
From: FT Leonard Wood, MO
Getting a new windshield installed today. There's $200 that could be used for mods down the drain. Gonna take my Kenwood in to fixed as well. Some one buy my xbox so I can buy my rear rotors/pads!!!
Last edited by jerseystyle; Jun 12, 2011 at 07:09 AM.
Thread Starter
Joined: Feb 2008
Posts: 5,134
Likes: 3
From: FT Leonard Wood, MO
Engine bay shot.

SAMCO hoses
ARC Rad/Oil Caps
ARC Cooling plate (touched up with my blow torch)
Gallery dress up kit
NISMO intakes
Will get a better shot of the whole bay when I clean it up some!

SAMCO hoses
ARC Rad/Oil Caps
ARC Cooling plate (touched up with my blow torch)
Gallery dress up kit
NISMO intakes
Will get a better shot of the whole bay when I clean it up some!
Last edited by jerseystyle; Jun 8, 2011 at 04:23 PM.
Thread Starter
Joined: Feb 2008
Posts: 5,134
Likes: 3
From: FT Leonard Wood, MO
Thread Starter
Joined: Feb 2008
Posts: 5,134
Likes: 3
From: FT Leonard Wood, MO
Yeah a buddy of mine parted out his G35 and found out that ARC stuff is like gold haha
Last edited by jerseystyle; Jun 20, 2011 at 01:48 PM.
I am looking for an ARC combo tank. Hate the looks of the plastic one. Someone here in the states should produce one.




it was a cheap solution to an annoying problem.
