Hey gang New Vendor and NE locals checking in
Thread Starter
Vendor - Former Vendor
iTrader: (7)
Joined: Jun 2009
Posts: 505
Likes: 1
From: Lansdale, PA
Hey Gang, Just starting a thread to introduce our shop and some of the services we offer. We Just became a vendor on this site and didnt want to not introduce ourselves. We have been trolling for a little while and noticed some customers we already know. But hope to meet some more of you guys in person. Anyway, here is a little "about us"
R/T Tuning is located about 40 minutes north of Philadelphia, In Lansdale, PA. We are a full service 23,000 square foot tuning shop and do just about everything as we have been for 7 years. From general maintenance to 1000+ horsepower top to bottom vehicle builds.We even offer on site secure car storage!
We have a Dyno Jet in-ground 2wd dyno. On that dyno we do Up-Rev Osiris Protunes and Reflashing . We have had great results with the Up-Rev Osiris on cars with just boltons as well as with Twin Turbo and supercharged cars. We are also factory trained AEM,TXS Utec, Apex’I Power FC, and Hondata Tuners.

We also do full street and race alignments on our Hunter DSP600 Digital Alignment rack.


We are equipped to do full corner balance as well as stock vehicle alignments. We also keep most suspension arms and adjustment bolts in stock from a variety of manufacturers just in case you run out of adjustment.
Our alignment technician is serious about making your vehicle handle and look its best. A lot of shops say the car is “too low” for the rack. At R/T Tuning no car is too low.
This car has no problem getting on our rack.
We can source you parts, as well as install them. We also aren't afraid to get our hands dirty doing routine maintenance

We offer parts from these manufacturers. We don't sell parts that we don't use on our own cars. We go drifting and racing regularly and know what works and what doesn't.
R/T Tuning
635 W 3rd st
Lansdale,PA
215-855-5565
www.rttuning.com
R/T Tuning is located about 40 minutes north of Philadelphia, In Lansdale, PA. We are a full service 23,000 square foot tuning shop and do just about everything as we have been for 7 years. From general maintenance to 1000+ horsepower top to bottom vehicle builds.We even offer on site secure car storage!


We also do full street and race alignments on our Hunter DSP600 Digital Alignment rack.



Our alignment technician is serious about making your vehicle handle and look its best. A lot of shops say the car is “too low” for the rack. At R/T Tuning no car is too low.

We can source you parts, as well as install them. We also aren't afraid to get our hands dirty doing routine maintenance

We offer parts from these manufacturers. We don't sell parts that we don't use on our own cars. We go drifting and racing regularly and know what works and what doesn't.
ACT-AEM-AFE-APS-Apex’i-ARP-ATI-ATP-Agency Power -Altered Atmosphere-Autometer -Blitz-Borla-Brian Crower -COBB Tuning-CP Pistons-Carbing -Carillo-Clutch Masters-Cometic Gasket-Crower-DeatschWerks-Defi -Eagle-Eibach-Energy Suspension-Enkei-Ferrea-Fidanza-Forced Performance-GReddy-GT-Spec-Gates-Goodridge-HKS-Hawk-Hotchkis-Invidia-K&N-Manley-Mishimoto -Motul-NGK-Okada Projects-Origin Lab-OMP -Power Enterprise-Project Mu-Prothane-Pyrotect-RC Engineering-Red Line-Skunk 2 -SPL Parts-SPEC-Sparco-Seibon-Stoptech-Tanabe-Takata-TC Sportline-Technafit-Tein -Thermo-Tec-Turbo XS -UpRev-Vibrant-Walbro-Work Wheels-Whiteline
So come on down and say hi,check the place out, kick the tires what have you. See you soon!R/T Tuning
635 W 3rd st
Lansdale,PA
215-855-5565
www.rttuning.com
Last edited by Vince@R/TTuning; Aug 18, 2009 at 06:19 AM.
We offer parts from these manufacturers. We don't sell parts that we don't use on our own cars. We go drifting and racing regularly and know what works and what doesn't.
www.rttuning.com

Also dig the "no car is too low" theory, we would get along well
I spoke to you earlier about an engine swap for a motor IPP is building for my 06 revup. I'm thinking of dropping the engine I'm swapping out into an old 72 240z and retrofitting it. Is that a project you guys could pull off? Very interested.
Thread Starter
Vendor - Former Vendor
iTrader: (7)
Joined: Jun 2009
Posts: 505
Likes: 1
From: Lansdale, PA
Trending Topics
Thread Starter
Vendor - Former Vendor
iTrader: (7)
Joined: Jun 2009
Posts: 505
Likes: 1
From: Lansdale, PA
We take care of you New york guys all the time.... we just had a guy come from long island and we have a guy coming from buffalo on Monday....
Make a day out of it...come down hang out....maybe have a good philly cheesesteak...
Make a day out of it...come down hang out....maybe have a good philly cheesesteak...
i gotta get down there..i hit ur other thread up...but do u tune ss box? i may just temporarily be retuned with it for this summer heat and humidity and then go osiris over winter and change some things up for more boost..lemme know if u do and when i could get in if so
Thread Starter
Vendor - Former Vendor
iTrader: (7)
Joined: Jun 2009
Posts: 505
Likes: 1
From: Lansdale, PA
i gotta get down there..i hit ur other thread up...but do u tune ss box? i may just temporarily be retuned with it for this summer heat and humidity and then go osiris over winter and change some things up for more boost..lemme know if u do and when i could get in if so
[QUOTE=Vince@R/TTuning;7639535]We have done several SS boxes. we could get ya in by the end of Aug early September pretty easily. let me know what ya wanna do
one more for ya....have u guys done any 2.87 pulley vortech setups?how do u feel about it on stock block and all? many are doing it... im trying to figure out if i can swing doing injectors, pump and osiris tune for the 2.87 pulley now or if im gonna wait till over winter and just re-tune what i have for now
one more for ya....have u guys done any 2.87 pulley vortech setups?how do u feel about it on stock block and all? many are doing it... im trying to figure out if i can swing doing injectors, pump and osiris tune for the 2.87 pulley now or if im gonna wait till over winter and just re-tune what i have for now
I'm thinking about getting different lowering springs or true coilover setup in the next year or so, which will require me to get a camber kit at least for the rears. Can you PM me pricing on doing a 4-wheel alignment with adjustable rear camber and toe kit? I'm thinking alignment would be a once per year thing so I would want to factor this into my yearly 'budget'. Thanks!



