@theianmcdougall: Be carefull!!! That basketball hoop might fall on your car too! Haha jk. I don't wanna see another z getting damaged

 

read through the last page

it did

happened 2 weeks prior to 350zdan's falling on his

 

Oops. Ouch! Sorry to hear bro.

 

What do you guys think of the following wheel specs:

F: 19x11 +12
R: 19x12.5 +12

The only part that has me worried still is inside front wheel clearance, the others don't worry me too much as I have found setups that go into similar areas...

The front is equally aggressive as a 19x9.5 -7mm and the rear is equally as aggressive as a 19x10 -20mm.

So, it's not crazy aggressive, but still not too bad.

 

Thanks E.. Your vid is super sick!!

 

the fronts shouldn't be too bad. im running 18x11 -0 on my set up right now and i dont have any turning issues at all.

 

Cool, I was sort of worried about that one..

I'll still be 12mm closer to everything on the inside though.. Still worried a bit :s

Have you looked under the car to see how tight the inside of the wheel is to anything?



Edit: This guy did it, didn't mention if it rubbed anything or not. I sent him a message and asked.
https://my350z.com/forum/nolazcc/422...-big-pics.html

 

Can someone be a real baller and run an aggressive 18/19 stagger? that would look ****

 

http://zilvia.net/f/wheels-tires/361...5x114-3-a.html
someone buy these sick azz wheels and do it right on a Z please!! wish i had the money to buy it....

al@pha - thats my homie ryan ride, just to let you know the front fenders were replace with wider ones. not sure sure how much wider they were though, but im pretty sure those should fit under stock fenders. just depend on the tire size your going to run

 

^^^^^wowwww those wheels are SICK!!

 

^^ yup saw those on Friday and was like damn... would buy but have something else up me sleeve

 

Yah I saw the aftermarket fenders. I'm positive those will work with stock fenders, other people have done more aggressive offsets than that.

I'm mainly concerned about the inside clearance on the suspension parts when turning etc.

 

Hey guys I was wondering if you guys can help me
I don't know a lot but can you help me with these following specs?

SSR SP1s + Falken 452s

First:
19x9.5 -3, 225/35
19x10.5 -13 245/35 or 40

Second:
19x9.5 -13 225/35
19x10.5 -16 245/35 or 40

Im getting Stance GR+ (low enough to close the gaps) but don't plan on getting spacers unless its necessary. Im willing to roll fenders as well. I want to be as aggressive as you guys but I know its hard.. haha. So my question: is either spec + the coils get me at a nice acceptable stance? Will there be a small poke (which is what i want too)?

FYI, I like Royal T, Toby, miltdoggie(?), windsorvr and some other guys whose names I dont remember lol my bad... your stances are what I want

Thanks for the help guys

 

Go with 35 series tires..

As for offsets it depends how wide rims you want and negative offset you want. It all depends what your looking to achieve. Give more info.

 

The first setup you posted is what I run!!! Flush in front small poke out back

 

shiiieeet you better be ready for a lot of trial and error. Even if we tell you what to get you'll still need to do a lot of adjustments with your fenders/camber/ride height.

anyway 35series and -16 is nice. Thats what im running out back with 235/35. Good luck

 

Same here! So tempting to log in on paypal and click send! But im good, I got lots to take care of before a new set comes! ...

 

yes, this. -3 will be weak.

 

i love how people want the look, but dont want the headaches..
the "look" is more of a lifestyle, they think, hellaflush!, sweet....
wait, i have to change the way i drive....wait, i have to deal with lip/undercarriage/exhaust/suspension damage, wait, what!?!? fender damage!!?!?

ima raise it up an inch lol.

 

such a great post...

you should've seen toby and me driving to charlotte with the ISO caravan....throwing up sparks the entire way there lol.