Graffiti motorsports harness bar
#22
Registered User
iTrader: (16)
Join Date: Feb 2007
Location: N. Virginia
Posts: 1,123
Likes: 0
Received 0 Likes
on
0 Posts
Does anyone have a copy of the instructions laying around? Or know what hardware we should use to mount this thing in.
Would acquiring the hardware Sparco uses for their harness bar possibly work?
Would acquiring the hardware Sparco uses for their harness bar possibly work?
#23
New Member
iTrader: (71)
The bar that I bought was used and didn't come with instructions. the two bolts that anchor the seat belts at the top are too short, so I bought
2 EACH STEEL HEX CAP SCREWS GR8 7/16" -20 X 2-1/4" ZINC YELLOW
2 EACH STEEL HEX CAP SCREWS GR8 7/16" -20 X 2-1/2" ZINC YELLOW
4 EACH STEEL SAE FLAT WASHER GR9 7/16" ZINC YELLOW
the original OEM screws are 2 inches long so I bought a set that is 1/4" and one set that is 1/2" longer just in case. For the achor bolts that are located on the floor of the trunk compartment I bought
2 EACH SST SOCKET HEAD CAP SCREWS A2 M8 X 25MM METRIC
2 EACH SST SOCKET HEAD CAP SCREWS A2 M8 X 50MM METRIC
10 EACH SST THICK FLAT WASHER TYPE 316 5/16"
I bought several sizes just in case, don't want to have to make another trip to the screw products store. the spares just go in the bolt bins. I haven't completed the installation
because I just picked up the bolts today.
2 EACH STEEL HEX CAP SCREWS GR8 7/16" -20 X 2-1/4" ZINC YELLOW
2 EACH STEEL HEX CAP SCREWS GR8 7/16" -20 X 2-1/2" ZINC YELLOW
4 EACH STEEL SAE FLAT WASHER GR9 7/16" ZINC YELLOW
the original OEM screws are 2 inches long so I bought a set that is 1/4" and one set that is 1/2" longer just in case. For the achor bolts that are located on the floor of the trunk compartment I bought
2 EACH SST SOCKET HEAD CAP SCREWS A2 M8 X 25MM METRIC
2 EACH SST SOCKET HEAD CAP SCREWS A2 M8 X 50MM METRIC
10 EACH SST THICK FLAT WASHER TYPE 316 5/16"
I bought several sizes just in case, don't want to have to make another trip to the screw products store. the spares just go in the bolt bins. I haven't completed the installation
because I just picked up the bolts today.
Last edited by Dan Garcia; 03-26-2012 at 03:19 PM.
#24
New Member
iTrader: (71)
Used the 2 gr8 7/16" -20 x 2-1/4" zinc yellow on the top seat belts
1 each sst socket head cap screw a2 m8 x 25mm metric and
1 each sst socket head cap screw a2 m8 x 50mm metric
but should be substituted by an a2 m8 x 35mm metric.
The bar has a spacer welded to the bottom of the right rear
anchor plate.
The bar fits nicely. Will post pictures as soon as i get a chance.
1 each sst socket head cap screw a2 m8 x 25mm metric and
1 each sst socket head cap screw a2 m8 x 50mm metric
but should be substituted by an a2 m8 x 35mm metric.
The bar has a spacer welded to the bottom of the right rear
anchor plate.
The bar fits nicely. Will post pictures as soon as i get a chance.
#26
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
You don't sit int he passenger side do you? I don't, so it doesn't matter. Also the pass side of my car isn't that bad, i could easily ride in it for a 4 hour drive to the track.
Thread
Thread Starter
Forum
Replies
Last Post
ars88
Zs & Gs For Sale
18
04-04-2016 07:52 AM