clemlover15

iTrader: (3)

I just looking for anyone else that has gone twin turbo is the Toronto area, if so who tuned your car?
I'm looking for a tuner that can tune TurboXS UTEC ecu.

Reality350

iTrader: (25)

Hi,

I thought you were going to use the shop on Esna park?..
You may want to see if mike from AAM is going to make another trip up north. I am sure he is familiar with that ecu.

R350z

clemlover15

iTrader: (3)

Ya KHF is doing all the work I'm just not a 100% sure on who will do the ECU tune, the guy they want to use does not have a load bearing dyno and you can't tune the car at different loads. You will have tp tune on the street and that scares me..I my go no neetronics they have the dnyno I want. They can also tune partial throttle postions.


Is there any other place???

Nitrouz

iTrader: (27)

subscribed. This would be good to know as I may be moving to T dot in the near future.

Pinky

Paul at neetronics is pretty good... and has pretty much tuned everything under the sun... AAM however is pretty good as well and tuned my friends greddy twin turbo set up in his G35 when they were up here in the fall

clemlover15

iTrader: (3)

where did AAM go for tunig, which dyno did they use?

I don't want to use a dyno jet, I need the kind paul has...

clemlover15

iTrader: (3)

hey when you move here we have to meet? I can untroduce you to the shop I use they are called KHF, but they are formally known as Kensai race team they have a team a Acura's that race in the Grand Am Cup in the states.
They work and ability is IMO the best!!

They have built by far the most FI Z/G35 that I am aware of in the TO area.

Reality350

iTrader: (25)

I hope you still have your Z when you do move here. You have the nicest Z by far

Best of luck with your ride.

R

Reality350

iTrader: (25)

Clemlover,

Mike used this shops dyno when he was in T.O, "Autoworks Service Center".

I am not sure where he actually worked on the vehicles he tuned, but I do know that "bachelor" was one of the participants in these tuning sessions. You may want to send him a pm and ask.

Good luck with the tune, and please keep us informed of your progress.

Cant wait for summer meets, I am itching to check out the tuned Z"s in T.O.

R

clemlover15

iTrader: (3)

thanks man Im hoping to have it done by the end of feb....

juniortheo

out ve curiosity,how much did the set up cost you? There is only 1 guy in montreal that i know of that went twins,and its a g 35 automatic. Wondering what the cost would be for 6 speed 350z, i got quoted 12 000 u.s from a shop in boston???

clemlover15

iTrader: (3)

OK for my build nothing was cheap, but my shop took really good care of me.
The built engine was around $5000 CAN it could have been built much cheaper with eagle rods and an off the shelf piston. The ECU turboXS with map switch and senors were like $1100US the APS tuner TT was around $8500 CAN
the CJM return fuel kit with injectors around $1300 US. Clutch/suspension/cooling not included. Thats should make 500rwhp @ 13psi for sure.

Thats not to say anyone that wants to go with the Greddy kit and stock motor and not a return fuel could do it for way under $10,000 CAN instaled.
that could make 400rwhp @ a safe 8psi

clemlover15

iTrader: (3)

some US shops have jacked up their prices because they can, the demand for this kind of stuff is higher people will pay for it down there. I was quoated $3140 just for the install and $600 for a tune by a big US name.

My guys will do the install for $2000 and tuning might be the same but in CAN funds....and in my backyard not 1000 of KMs away.

Hey the only place that I would have honeslty risked shipping my car to would have been www.forgedinternals.com or www.racemrc.com

xjongsangx80

iTrader: (15)

Damn..that's expensive.. I thought Greddy TT makes 400whp @ 6psi on stock motor..

Reality350

iTrader: (25)

Clemlover, you are killing me here!!! hahah, I need to check out your ride come summer time. If all goes well for you I will most definitely take my ride to the same shop. (khf you reading this!)

Cheers,

R

Edit: My shop of choice as it stands now, would have to be Forged performance.. But that wont happen for another 3 years..

clemlover15

iTrader: (3)

I don't think 6 psi will make 400 but hey maybe.

Ya its not cheap but I took the road of getting the best possible parts and having peace of mind for years to come.

I didn't want to get a cheaper part and worry about it not being as reliable as a superior one. Im my mind you get what you pay for...

clemlover15

iTrader: (3)

You should drop by the shop when its getting installed to see the process for yourself. They have done many greddy TT's and Vortech's but this will be their first APS TT.

The motor is real behind but there is no rush I'll let you know when its there, I'm hoping for sometime in mid feb, it should take them over 2 weeks to get her done, I'll let you know for sure.

Reality350

iTrader: (25)

Dam, I am there! Please dont mock my stock 35th..

R

clemlover15

iTrader: (3)

never, were on the same team man.

clemlover15

iTrader: (3)

100% offical I will be using Paul at neetronics for tunning. I went up there and spoke to him yesterday to make sure that they can do what I want. They also tuned my integra back in the day, they are trully the best at what they do hands down.