2boosted4u

iTrader: (4)

i realize that it does differ slightly for each car but i have a 03 track non revup and i am looking at the mrev2 lower intake, 5/8" spacer, aem cold air, test pipes, and possibly kinetix upper manifold...what should i expect out of this?? (whp/wft/lbs) i have a stillen exhaust....thanks in advance!

Zilvia

iTrader: (1)

maybe max of 25-30hp....but a whole lot of added throttle response

2boosted4u

iTrader: (4)

is there anyother intake upgrades that are out there?? im just lookin to do all bolt ons and get a custom tune...with out FI

ssgohan434

iTrader: (13)

dont get a cold air intake.... it might even make you lose power. Go with the JWT popcharger, K&N filter in stock box, or upgrade to the '06 stock box since they have a venturi ring which makes the airflow better to the plenum, or the more $ one's such as stillen, ARC, K&N.

id say all those mods should put you 25 to 30whp over stock.

SuperBlack350z

iTrader: (59)

why would you get a intake spacer and then get a kinetix manifold?

bbs350z

iTrader: (85)

your names 2boosted4u, and you DO NOT wanna run f/i??

cbr900son

iTrader: (4)

kintex also makes a upper not just the ss

Z1 Performance

iTrader: (564)

get the plenum spacer and skip the Kinetix manifold.

intake wise, it makes 0 difference what you run - so it's your call there, short ram, cold air...all will net you similar gains

also I don't see a UTEC or any means of tuning there, and that is the thing that will really wake it up. Post tuning, expect about 260 whp

singh

iTrader: (2)

IMO, those mods will give you little to nothing. Except the test pipes, the rest will simply just empty your wallet. If you really want noticeable power, save for a turbo kit. I don't see the point in those mods. (except the test pipes)

Q45tech

$100-$150 per added NA horsepower is the usual tariff.

ke0ki2k

iTrader: (2)

thats an EXTREMELY rich guesstimate. rich as in completely unrealistic. You arent gonna get 25-30 hp without doing a whole lot more than a couple breather mods on stock maps. With everything you listed....not sure. that MREV2/Spacer is more effective on Revup motors but it will improve midrange power/torque more than anything. Heres a good setup for ya: JWT pop charger, a motordyne plenum spacer, strup/Alphawerks/Crawford headers, AAM test pipes. Regardless, dont expect more than 20 horsepower without cams/utec/tune on top of the boltons. Why youd do a 5/8ths inch plenum spacer with an MREV2 is beyond me...its been dyno proven that bigger spacers with an MREV2 negate its positive outcomes, it works best with a 5/16ths inch spacer from motordyne

jonnylaw

iTrader: (3)

+1

ke0ki2k

iTrader: (2)

...after reading all the responses..if youre gonna completely replace the stock intake manifold...bite the bullet. Pre-order a Cosworth intake manifold for a Grand. It looks like it will be the best intake related product to come across our little community. Stillen exhausts havent shown any power gains but I have seen dynos showing some of AAM's exhaust products to produce power. Correct me if im wrong? cause i have seen AAM claiming "20 hp" gains on their intakes lol..

2boosted4u

iTrader: (4)

i have a shop that would do the custom tunes unless you really think that it wont do much.....im saveing up for the turbo kit and i just want some power in the mean time and my last car was boosted...

TheBlackPearlZ

iTrader: (15)

honestly...theres no point in buying all that stuff if you are going to eventually go FI. most if not all of it will be replaced by the turbo kits parts.

so i think your wasting your money if you do buy all that stuff

zyou8er

iTrader: (1)

Sorry for hijacking the post, but im wondering what you guys reccomend on a 06 base 350z? Thanks.

bbs350z

iTrader: (85)

an lsd and a turbo

2boosted4u

iTrader: (4)

well not im looken at just a intake and 5/16 spacer instead of them mrev2??

ke0ki2k

iTrader: (2)

or if youre a poor man like myself, Motordyne MREV2 and 5/16th's inch plenum spacer. Biggest difference bolton for revup engines like ours ;]

and for you, boosted, just do a Jim Wolf Popcharger and a 5/16ths plenum spacer, maybe a test pipe. all cheap power adders. wont be hackin off seconds on your quarter mile....but it will be quicker and a lil more fun to drive.

2boosted4u

iTrader: (4)

right on! will do....i was only looken at the mrev2 cause i was goin to get it and teh 5/16 spacer for $350....thats why i thought for the money it oculd be wel worth it