Notices

Differential side plate pulls out

Thread Tools
 
Search this Thread
 
Old 02-21-2016, 04:08 PM
  #1  
ronhock
Registered User
Thread Starter
 
ronhock's Avatar
 
Join Date: Feb 2016
Location: California
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default Differential side plate pulls out

The SLIP VDC BRAKE and ABS lights were on when I bought the car (03 350Z touring). I found the error was from the LR ABS sensor. Turned out the side plate was pulled out from the diff enough to mis-align from the abs sensor and sling oil all over.

I dropped the diff, cleaned it all up, replace the circlip with a new one (that is noticeably beefier) from Nissan. New seal, too.

I doubt I've put a hundred miles on it and the lights are back on and the side plate has pulled out again. No oil yet but lights just came on a few miles ago.

Anyone know what's going on to pull on that side plate like that?

Thanks in advance.
Old 03-02-2016, 12:24 PM
  #2  
350ZZJoe
New Member
iTrader: (2)
 
350ZZJoe's Avatar
 
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 370
Likes: 0
Received 1 Like on 1 Post
Default

That's very weird. I'm assuming you have the OEM VSLD in your car?

I had the same problem but I have an OS Giken LSD and I actually machined my stub axles to accept the circlip rather than buy new stub axles. So my problems came from that, but they have been resolved now.

I'm guessing its possible there is an issue with the diff itself. Could be a question for Nissan.
Old 03-02-2016, 01:49 PM
  #3  
ronhock
Registered User
Thread Starter
 
ronhock's Avatar
 
Join Date: Feb 2016
Location: California
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

Thank you for your reply. I've asked about this on three forums and you're the first to have experienced it.

So, do I just call the local Nissan service department? Or is there some more central place to ask Nissan questions?
Old 03-05-2016, 11:25 AM
  #4  
350ZZJoe
New Member
iTrader: (2)
 
350ZZJoe's Avatar
 
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 370
Likes: 0
Received 1 Like on 1 Post
Default

Yeah I'm not sure why it would still be sliding out with the new clip installed. I think going to Nissan is going to cost you a good amount of money. I'd look around for a used differential and just install that. Would probably be a cheaper route.

Nissan will want to take everything out of car, inspect, then replace with brand new OEM parts. Going to cost a lot of $$$$.
Old 03-05-2016, 01:25 PM
  #5  
ronhock
Registered User
Thread Starter
 
ronhock's Avatar
 
Join Date: Feb 2016
Location: California
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I appreciate your input. I see used diffs for around $300 on eBay. Not the end of the world but I admit I was hoping for a minor miracle.

Thanks.
Old 03-21-2016, 10:33 AM
  #6  
ronhock
Registered User
Thread Starter
 
ronhock's Avatar
 
Join Date: Feb 2016
Location: California
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I changed the CV axle and the output shaft popped out after about 50 miles. So now I think I should be shopping for a used diff. I'll match VLSD and year-range, but does it have to have come from a manual transmission car? Will an AT diff interchange?
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
chuddly
2003-2009 Nissan 350Z
26
02-24-2016 06:53 AM
DrGOLD
Misc.
4
02-16-2016 08:01 PM
shadowm891
Engine & Drivetrain
1
02-16-2016 12:13 PM
Scott Morris
New Owners
8
02-16-2016 08:02 AM
APTech
Southern California
4
02-16-2016 07:48 AM



Quick Reply: Differential side plate pulls out



All times are GMT -8. The time now is 02:34 PM.