350Z Concept LED Test fit...
#63
Registered User
Join Date: Feb 2003
Location: Houston, Tx.
Posts: 141
Likes: 0
Received 0 Likes
on
0 Posts
I actually like the darker more burnt orange look of them. I wish the upper stock parking light was a little darker now. Oh and a little hint on installing these LED's; you don't have to remove the front tires. Just jack up each side of the car, as you do each side, just far enough to get the tire off the ground and there is plenty of room to remove the 3 plastic rivets and the 1 screw. You don't even have to remove the inside fender well. Just pull it down or back out of the way. On the pasenger side, because of the windshield fluid tank, I removed the lower bumper screws on the passenger side and all the top bumper plastic rivets. I got under the car and you can see the washer tank and the reflector. I just pulled the bumper forward a little and used a short screwdriver to unscrew the stock reflector. Just be careful pulling the bumper forward. You don't want to use to much force. You only have to pull it foward a couple centimeters to be able to easily reach the screws front under the car. The car is jacked up a bit while doing this so it is no problem to get your head under there and do this.
#68
Registered User
Join Date: Jun 2002
Location: In a Village!
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
Hey... here's an idea! For those who already have the ones StrictlyZ released make an insert we can use. You'd get a lotta extra $$$ since many of us already have these
#69
Vendor - Former Vendor
Thread Starter
iTrader: (121)
Join Date: Oct 2002
Location: NY
Posts: 2,363
Likes: 0
Received 0 Likes
on
0 Posts
I can do that, by making a metal stamped cover. BTW the molding still on the way. If I do make them will there be many people interest? If so, Once i got the strictlyZ LED. StrictlyZ wanna work with me on this? I can have it done in 2 weeks. Let me know.
Concept LED PCB board box is ready. Front two pieces will be seal together with sonic wave shack. This way for sure no water will go in and burn the LED circuit.
Concept LED PCB board box is ready. Front two pieces will be seal together with sonic wave shack. This way for sure no water will go in and burn the LED circuit.
#71
Registered User
iTrader: (1)
idea!!!!
I have an idea!!! Excuse me if this already exists and let me know how to get mine! But wouldn't it be neet to have the Z emblem on the side fender to have a back lit circle around it?!! I know this is somewhat a copy of the bmw Z3. But they do have the "Z" thing in common. I would love to have the emblem light up on my car. (not really bright lighting but kind of a soft white)!!!!! any thoughts opinions?,......
loving this thing,
calvin
SS touring, 6mt,3M,LED's,DVDplayer&7"wide screen, all other factory options
loving this thing,
calvin
SS touring, 6mt,3M,LED's,DVDplayer&7"wide screen, all other factory options
#72
Vendor - Former Vendor
Thread Starter
iTrader: (121)
Join Date: Oct 2002
Location: NY
Posts: 2,363
Likes: 0
Received 0 Likes
on
0 Posts
I have thought of that before. I even had a sample done. But I don't know if people willing to replace their Z side logo. Since the 3M tape is very hard to peel off and might scratch the paint. If I get enough support on this then I would consider to do it. Currently I have 6 350Z new products on hand. OEM carbon fiber wing and headlight cover is in stock. Watch for more new items!!! I know all of you cannot wait on the LED light, but right now it is all under the molding factory's control. Once it is done... 500 sets all be out right away!!!
#73
Registered User
iTrader: (1)
Join Date: Oct 2002
Location: Orange County, CA
Posts: 5,007
Likes: 0
Received 0 Likes
on
0 Posts
If you make the "glowing" side Z logo I would take a set since my Z emblems were vandalized anyways. It would have to be a pretty good deal, considering those side logos run $20-25 each so I doubt most people would be willing to spend more than $40-50 each.
Still waiting patiently for those Concept LEDs!!!
Still waiting patiently for those Concept LEDs!!!
#77
Registered User
Join Date: Jan 2003
Location: Chicago
Posts: 64
Likes: 0
Received 0 Likes
on
0 Posts
those look nice...I will take a pair of amber one's. Oh and on the idea of the z emblem, I thought about the same thing. I would definetly would buy a pair. I would make the whole light smoked, and then with the silver Z over it. That woud look cool.
#78
Registered User
Join Date: Jun 2002
Location: In a Village!
Posts: 982
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by JDMZ33
I can do that, by making a metal stamped cover. BTW the molding still on the way. If I do make them will there be many people interest? If so, Once i got the strictlyZ LED. StrictlyZ wanna work with me on this? I can have it done in 2 weeks. Let me know.
Concept LED PCB board box is ready. Front two pieces will be seal together with sonic wave shack. This way for sure no water will go in and burn the LED circuit.
I can do that, by making a metal stamped cover. BTW the molding still on the way. If I do make them will there be many people interest? If so, Once i got the strictlyZ LED. StrictlyZ wanna work with me on this? I can have it done in 2 weeks. Let me know.
Concept LED PCB board box is ready. Front two pieces will be seal together with sonic wave shack. This way for sure no water will go in and burn the LED circuit.
Two things I just don't want to do... take off the front bumper AGAIN and buy something that is redundant. The LED settings on the Strictly Z strip is 100% stock 3 bulb LED. I saw the ones you did in blue and they look like there is many more LED Bulbs. Why they look cool, the metal insert idea definately wouldn't work . I could rally up a few people just by posting a link to the picture to see if we could get some interest to build. Let me know - more then happy to work for you if it benefits me!
#80
Registered User
iTrader: (1)
Join Date: Mar 2003
Location: Key West
Posts: 445
Likes: 0
Received 0 Likes
on
0 Posts
D-OOOOOOOOOOOOOHHH!
WHY COULDN'T I HAVE SEEN THIS A FEW DAYS AGO I JUST BOUGHT LED'S CORNERS BUT NOT THE CONCEPT STYLE I WOULD DEFINITLY PREFER THESE. PLEASE LET US KNOW WHEN AVAILABLE.
WHY COULDN'T I HAVE SEEN THIS A FEW DAYS AGO I JUST BOUGHT LED'S CORNERS BUT NOT THE CONCEPT STYLE I WOULD DEFINITLY PREFER THESE. PLEASE LET US KNOW WHEN AVAILABLE.