Top Secret Diffuser Exhaust Fitment List
04-28-2008, 08:54 AM
#23
Registered User
Join Date: May 2006
Location: Maryland
Posts: 275
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TayTaythatsme04
HKS Hi Power Ti (fits with dremeling )
T
T
05-22-2008, 02:48 PM
#31
Banned
iTrader: (28)
Join Date: Dec 2005
Location: Spotswood NJ
Posts: 5,510
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by stylett9
lol, seriously, that's the second time he's posted he'd post pics. come on and post them!!!!
Only if everyone says "Julian is god"...Three times fast!!Then farts..
05-22-2008, 04:11 PM
#32
Registered User
iTrader: (6)
Join Date: Nov 2006
Location: The Northwest
Posts: 1,141
Likes: 0
Received 0 Likes
on
0 Posts
I will get some pics of mine soon as well, fiance jacked my digital camera last time I was in Seattle....
I am going to fabricate some brackets so it will fit tighter to the bumper. Its on right but there is about a quater inch gap where the sides (not vortex gen's) should be flush. The issue I found is the give in the bumper, bumper pulls down rather then the diffuser being pulled up by the bumper if it was more rigid....
I am going to fabricate some brackets so it will fit tighter to the bumper. Its on right but there is about a quater inch gap where the sides (not vortex gen's) should be flush. The issue I found is the give in the bumper, bumper pulls down rather then the diffuser being pulled up by the bumper if it was more rigid....
05-24-2008, 03:55 AM
#37
Banned
iTrader: (28)
Join Date: Dec 2005
Location: Spotswood NJ
Posts: 5,510
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Jim@Showstoppers
Doesn't look like too much dremeling, very nice Julian !
You should make them flat with no clear, to look like Dry carbon..
05-24-2008, 02:14 PM
#38
Registered User
iTrader: (9)
Join Date: Sep 2005
Location: LBC or In the Hills of Chino
Posts: 1,436
Likes: 0
Received 0 Likes
on
0 Posts
Alright, maybe i'm an f-ing idiot but I tried installing thise diffuser today with the Nismo and the brackets that mastergrade supplies are just not aligning correctly. They are not frabricated at the right angles even. Does anyone have a very good picture of where the bracket attaches to on the car on both sides? To me it looks like on the drivers side it needs to attach to a "blue screw" that is poking out behind the rear fender with the "z" looking bracket and the passenger side with the "L" looking bracket attaches somewhere? Please help.
05-24-2008, 02:15 PM
#39
Registered User
iTrader: (9)
Join Date: Sep 2005
Location: LBC or In the Hills of Chino
Posts: 1,436
Likes: 0
Received 0 Likes
on
0 Posts
Julian can you post a picture of your bracket setup? Did you use the same brackets mastergrade provides? Also, did anyone dremel the inside of the diffuser where it meets under the bumper to get it to sit flush?
05-24-2008, 03:05 PM
#40
Originally Posted by buffmanjeff
Alright, maybe i'm an f-ing idiot but I tried installing thise diffuser today with the Nismo and the brackets that mastergrade supplies are just not aligning correctly. They are not frabricated at the right angles even. Does anyone have a very good picture of where the bracket attaches to on the car on both sides? To me it looks like on the drivers side it needs to attach to a "blue screw" that is poking out behind the rear fender with the "z" looking bracket and the passenger side with the "L" looking bracket attaches somewhere? Please help.