A little too loud...
#21
Registered User
Thread Starter
Join Date: Dec 2012
Location: Orlando
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
Yep, Thats my page!
And back on topic lol. Im thinking Resonators or ART pipes. Most likely going to try the Art pipes, and if its still to crazy ill throw in some resonators.
And back on topic lol. Im thinking Resonators or ART pipes. Most likely going to try the Art pipes, and if its still to crazy ill throw in some resonators.
#22
Registered User
Honestly it'll still be loud with ART pipes lol, i swapped from AAM test pipes to ART pipes on my brothers Z and to me the only big difference was performance, i guess i could say it was a very very light amount quieter but thats stretching it. Might as well go ahead and do the resonator idea.
#23
New Member
iTrader: (29)
sweet car. I doubt the arts are going to quiet it down enough for you. Neither are resonated test pipes over non resonated. Best bet would be hfc or put in another resonator or muffler. I used to run art pipes with berks, now I run hfc with berks and the arts were louder for me.
#25
Registered User
Thread Starter
Join Date: Dec 2012
Location: Orlando
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
#26
Registered User
Thread Starter
Join Date: Dec 2012
Location: Orlando
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
Honestly, Id like to get HFC.. Just so its "legal" But im afraid my 2 step launch control will blow them out.. Does any one know if any HFC's that would be strong enough to handle it? I plan on Vortech'ing her this summer as well.
#27
Registered User
Thread Starter
Join Date: Dec 2012
Location: Orlando
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
Here is a link to what it sounded like a few days ago with stock cats.
http://www.facebook.com/photo.php?v=10200435370994424
http://www.facebook.com/photo.php?v=10200435370994424
#28
Registered User
iTrader: (3)
I have a set of Pypes unit's here on hand, "just in case" my Z's one go south.
The price is great and last a long time. here is a 3" set... just so you get the idea.
http://www.amazon.com/Pypes-Exhaust-.../dp/B00B3ZHNXS
Good luck
#29
Registered User
Thread Starter
Join Date: Dec 2012
Location: Orlando
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
I'm not sure anone is using the Mini-Cat's w/ Metallic substrate material here. I have run a few sets on cars that would 'Eat" normal cats. They hold up much better then normal units. I have yet to blow up these... Turbo, supercharger, etc.
I have a set of Pypes unit's here on hand, "just in case" my Z's one go south.
The price is great and last a long time. here is a 3" set... just so you get the idea.
http://www.amazon.com/Pypes-Exhaust-.../dp/B00B3ZHNXS
Good luck
I have a set of Pypes unit's here on hand, "just in case" my Z's one go south.
The price is great and last a long time. here is a 3" set... just so you get the idea.
http://www.amazon.com/Pypes-Exhaust-.../dp/B00B3ZHNXS
Good luck
#31
Registered User
Thread Starter
Join Date: Dec 2012
Location: Orlando
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
#32
Registered User
Join Date: Feb 2013
Location: Australia
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Rasp only in the 2000-2500rpm
I've got a supercat Australia muffler with high flow cats, and custom stainless steel extractors.. Once I put the extractors on the car formed a rasp noise when I accelerated hard through the 2000-2500rpm mark.. I'm thinking of getting resonators put in and a custom y pipe as the y pipe is still the stock one.. I'm
Hoping this will quiet car down suffiently and kill the raspy rattle..
Any info if this is on right path?
Hoping this will quiet car down suffiently and kill the raspy rattle..
Any info if this is on right path?
#40
Registered User
Thread Starter
Join Date: Dec 2012
Location: Orlando
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
Ive seen so many videos that make me angry because you want to hear more or they hold the camera to close and the audio sounds horrible, or they don't even rev. Sometimes your just like "Why was that even posted??". So thats my reasoning for putting this one together