g3t_t0rk

I pulled the wires out ot the plastic holder. Dont know where to put the wires back. Plz help!! see diagram below.


----------------------------------------
|10 1|
|11 2|
|12 3|
|x 4
|x 5
|13 6|
|14 7|
---------
|15 8|
|16 9|
----------------------------------------

g3t_t0rk

Sorry if I didn't put the thread in the right place!!

red roadster

Go to a web site called automotix. You can get online access to wiring diagrams for your year and trim level. Less than 10 bucks for 6mo. access. My access is for a 06 didn't know your year or which side.

g3t_t0rk

I need the driver's side window please!!

g3t_t0rk

I just bought the Automotix thing. It doesn't help whatsoever.

DavesZ#3

iTrader: (26)

What year is your Z?

g3t_t0rk

2003

DavesZ#3

iTrader: (26)

Start here..

https://my350z.com/forum/maintenance...anual-fsm.html

they have the wire color codes listed there. Download the proper FSM and look in the GW section to start.

g3t_t0rk

Same info as automotix... Page 20...

http://www.nicoclub.com/FSM/350Z/coupe/2003/bl.pdf

KornerCarver

iTrader: (2)

You might need to take your car to a dealer to get your problem resolved. Why did you pull the wires out of the plug?

g3t_t0rk

I was trying to do the window motor reset as the windows keep going down after opening my door. After doing some research on the boards, that's what seemed to be the problem. This is the first time I'm working on a Nissan so I didn't know how to remove the plug. I ended up making a bad mistake haha

g3t_t0rk

No one can help?

DavesZ#3

iTrader: (26)

Did you see a chart like the attached one in the GW section? Below it are a bunch of diagnostics steps. Each of them shows one of the connectors and identifies which pin and color for the wires in those connectors. Go through them and fill in the blanks for what you need. You may have to go to a different section to find the references to the door lock related pins.

KornerCarver

iTrader: (2)

Here is a wiring diagram for the power windows. I'm not sure where the plug is that you are talking about. Resetting the windows does not normally require removing any wiring.

DavesZ#3

iTrader: (26)

the only problem with that diagram is it doesn't have pin numbers so he won't know where in the connector each ones goes. I assume he removed the wires from the connector that goes to the driver door switch unit since that's the one with the window and lock switches.

Maybe if OP posts a picture that might put us all on the same page (so to speak).

red roadster

On the automix site, on the diagram for my 06, it showed connectors with the numbers of the pins. the connectors were numbered. d7 is the one, I think he has laid out, but his numbering doesnt match the diag. I am guessing that just the way he wrote it out. Any way you can then look at the component which has the corresponding plug number and that shows the pin number with the color code for the wire.
i will be more than happy to convert the plug pins and color code but I only have access to the 06. probably isn't the same. The info he needs is there he just needs to study it a little harder.

drvqz33

iTrader: (10)

Is OP talking about the wiring harness?

Because I have both passenger and driver side 03-05 harnesses out of the car and I can take pics of the connectors

DavesZ#3

iTrader: (26)

That might work, especially if he'd post pics of the connector in question. One slight problem is that the 2003 & 2004 cars has some slightly different wiring than the 2004.5 and later ones.

g3t_t0rk

Sorry for the late reply. Here's a pic of the connector

g3t_t0rk

Anyone! Haha I'm so close to getting these windows reset!