Bmurray's 2008 350z Progress Thread
Thread Starter
Joined: May 2011
Posts: 8,075
Likes: 92
From: Burlington, NC
These were all straight decals. They're not from Enkei. They're from this guy on eBay lol. He did them cheap. But yeah they may look like they're curved but they're all straight 100%
Thread Starter
Joined: May 2011
Posts: 8,075
Likes: 92
From: Burlington, NC
And either way it still wouldn't matter, if they were curved for the contour of the wheel, the words would be facing the same way so it would look the same, know what I mean?
Registered User
Joined: Aug 2011
Posts: 995
Likes: 1
From: coopercity, FL
I know you had both Megan single and agency power, which do you like better?....I know they look a bit different but did you notice a gain when you switched em. I know the agency might be a little lighter.
Thread Starter
Joined: May 2011
Posts: 8,075
Likes: 92
From: Burlington, NC
Agency looks better and is lighter yes.
The Megan had some weird noise when the engine was cold. Idk how to explain it other than it was very very high pitched. Almost sounded like a civic until the engine was warmed up.
The Megan had some weird noise when the engine was cold. Idk how to explain it other than it was very very high pitched. Almost sounded like a civic until the engine was warmed up.
Ok you've got my attention now 
, i've been looking at ways to get more out of the HR motor without FI...7-10hp increase seems pretty steep, i'll be waiting on results before i purchase.
have you looked into the NWP throttle bodies yet?
, i've been looking at ways to get more out of the HR motor without FI...7-10hp increase seems pretty steep, i'll be waiting on results before i purchase. have you looked into the NWP throttle bodies yet?
Thread Starter
Joined: May 2011
Posts: 8,075
Likes: 92
From: Burlington, NC
and NWP hasn't made any for the HR yet unfortunately. and not sure if the DE tb's would work or not
I'll call monday morning and figure out if we can work out some sort of test deal for the VQ35HR since i'm going to need a re-tune here in a few months anyways
Thread Starter
Joined: May 2011
Posts: 8,075
Likes: 92
From: Burlington, NC
i think they're DE tbs are 75mm. stock on hr is 60mm. stock on de is 70mm iirc. the jump from 60 to 75mm may be a little much. lol. but yeah see what they say. they're somewhat local to me, and one of the owners Aaron has talked to me on fb before releasing the DE tb kits. mention my name
Registered User
Joined: Aug 2011
Posts: 995
Likes: 1
From: coopercity, FL
Those seem to be some nice pulleys. Just aw a thread on them over by the 370z forums. http://www.the370z.com/engine-drivet...no-charts.html
I emailed them sometime ago about releasing a tb one for the hr but they had no plans to at that time.
I emailed them sometime ago about releasing a tb one for the hr but they had no plans to at that time.
Last edited by The_Assassin; Mar 16, 2014 at 06:16 PM.
Thread Starter
Joined: May 2011
Posts: 8,075
Likes: 92
From: Burlington, NC
Even though most of you have seen the other thread:
https://my350z.com/forum/intake-exha...r-project.html
May as well update this thread as well
Picked up 15whp and 11tq with some custom 3" intakes and a retune!
https://my350z.com/forum/intake-exha...r-project.html
May as well update this thread as well
Picked up 15whp and 11tq with some custom 3" intakes and a retune!
