Looking for best tuners locally
#1
Registered User
Thread Starter
Join Date: Apr 2009
Location: South Florida
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
Looking for best tuners locally
I'm located in South Florida, Broward County to be exact, just wondering about where I can go to get some tuning from a place that knows their stuff and is known to tune the 350z. I'm using the UTEC on the 2003 VQ35 motor. Thanks for the help in finding a place to get dyno tuned. Any 350z specific shops locally I'd be interested in getting ahold of as well. I may be getting other motor work done too. Looking for a Nissan specific shop.
#4
New Member
iTrader: (9)
#7
Registered User
Thread Starter
Join Date: Apr 2009
Location: South Florida
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
Any local shops in Broward or Dade County that do reputable work that anybody knows of that I can be referred to ?
I spoke to HP Logic, as soon as I get my Utec in I will be using them for tuning.
I spoke to HP Logic, as soon as I get my Utec in I will be using them for tuning.
Trending Topics
#9
Registered User
Thread Starter
Join Date: Apr 2009
Location: South Florida
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
#11
Registered User
Thread Starter
Join Date: Apr 2009
Location: South Florida
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
That's fine I just want to get it done. I have the VQ35DE from a maxima 2003 in my 2002 SE-R sentra spec v. I'm looking forward to the tuning and cams.
#13
Registered User
Thread Starter
Join Date: Apr 2009
Location: South Florida
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
there's not that much room at all, that's why I wanted to get a quote from a local shop. I think I'm just going to do it myself even if i have to end up pulling the motor. I have another car to drive. It'll have to be a project.
#14
SFZCC
iTrader: (19)
Join Date: May 2002
Location: Lake Worth, FL
Posts: 7,419
Likes: 0
Received 0 Likes
on
0 Posts
yeah, I think pulling the engine is the best way, because not only do you have to get to the cams to remove them, but you have to remove the front timing chain case to do this.
And unless you have the means to keep the valves closed while changing the springs you will have to remove the heads.
And unless you have the means to keep the valves closed while changing the springs you will have to remove the heads.
#15
Banned
Join Date: Jul 2006
Location: West Palm Beach FL
Posts: 72
Likes: 0
Received 0 Likes
on
0 Posts
#16
Registered User
Thread Starter
Join Date: Apr 2009
Location: South Florida
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
I'm looking for a reputable block machinist down here in South Florida. Looking to get a good price for the work as well as getting it done correctly. If you have used someone in the area PM me, preferably with their phone number and contact information. Thanks.
Going ahead with fully rebuilding the motor, wiseco pistons 11:1 96MM and Eagle Rods. Said screw it why not since to get the cams in it's coming out of the bay Help me find a good machinist!
Going ahead with fully rebuilding the motor, wiseco pistons 11:1 96MM and Eagle Rods. Said screw it why not since to get the cams in it's coming out of the bay Help me find a good machinist!
Last edited by kgkeen101; 06-01-2009 at 07:40 PM.
#17
SFZCC
iTrader: (19)
Join Date: May 2002
Location: Lake Worth, FL
Posts: 7,419
Likes: 0
Received 0 Likes
on
0 Posts
Larry at South Florida Crank in Lake Worth is great, he did th emachine work on my engine and a few others I know. H is usually backed up so speed is not a given but quality is 561-533-9932, if you go with him tell him Gus sent you, really great guy.
#18
Registered User
Thread Starter
Join Date: Apr 2009
Location: South Florida
Posts: 255
Likes: 0
Received 0 Likes
on
0 Posts
Thanks, I will give him a call tomorrow.
Thread
Thread Starter
Forum
Replies
Last Post