Anyone that has done UpRev eTunes - how do you know which file is loaded, and do the updated etunes take far less time to load than the original?

I just loaded a new tune and was wondering if there is a way to tell which file (tune) is on the ECU. I got a successful (?) completion message but the new eTune seemed to load way faster (~10sec) than the original (~2 minutes).
It's now making me wonder if anything was loaded at all. My ECU in Osiris shows "23710-AC406 stock flashed ECU." Seems to be the same as it was before I started.

Am I overthinking this? It sure would be good to know that I've got the right file loaded.

 

I just got my Osiris Standard today, and I can tell you that in the User Guide, it states that the first initial flash will take 1-2 minutes, and every flash from then on will take seconds.

I just went and logged my two 0-60mph launches and sent them in, says 2 weeks, how long did it take you to get yours?

Also, when I ordered from the Website, I chose what Mods I had done, and what RPM level/Idle level and what maps I wanted, I picked 2 maps of the 5 listed and made a track and DD map, but how do I access these maps or do I have to do an eTune to flash and that was just them saving my information at order? Has me confused.

 

The eTune (update) took only a week. Yea, I found out same about subsequent flashes taking a lot less time, though it would be nice if Osiris confirmed which file is loaded, and didn't constantly clear the log parameter settings - at least that's what always happens to me - what a PITA...

I got a base tune (via email) when I first ordered Osiris standard that came with 5 maps I requested - uses cruise control buttons to set.

No speed limiter, raised RPM rev limit to 6900, idle to 750 and asked for tune with WOT / 93 octane,

1. Full Tune -93 octane / WOT
2. Launch - 93 octane rev limit at 3000
3. Stock
4. Economy - 91 octane, rev limit at 4500
5. Valet - 30mph / 3000 rpm

The eTune update feels much better than the stock map though I haven't logged any serious runs with it yet. 2nd and 3rd spins the wheels if I don't feather the clutch just right - didn't do that too easily before.

 

I sent in for my first eTune update yesterday, can't wait to get it back. The base tune put a smile on my face, and doing the two 0-60mph launches data logging for the eTune lol.

 

I can confir that second and more e-tune writing are shorten than the first.
In my 350HR second write takes 30 sec, first about 2 minutes.
And for sure it was written right, i added a map on a "cruise slot" that in the first was not present

I think that software writes only differences in the second and more writing, for that is shorter. Remember that tech speaking Osiris "patch" the ROM "on fly", it does NOT write in the ECU rom all maps. So datas are written in body pc and ECU instructed to read from that insted of from the real ROM. So first time Osiris may be has to write all "program", other times only small data areas.
And for that it's possible to change "maps" using cruise control...

May be i'm wrong ???

 

Thanks. In my case all the maps continued and so I was just questioning why we have no way to see the actual map that's been loaded by name.

Also, do you find that your Cipher log parameter selections keep getting reset, and that you have to select them on each run? I wish Uprev had a quick way to select the settings needed for an e-tune without having to
go through and set-up the list every time.

Minor peeves but I'm really enjoying the new tune, much better than the original.

 

Umhhh....i have to check about Chiper log settings.
In TEORY these has to be stored so in next use of the program all is the same but i never look this....
I have used chiper for log 3 times but with different pc (or the same reinstalled) so ... i have to check this "bug"...

My car changed a lot with tunes, also with "simply" e-tunes (i live in Italy, only way to use Osiris is with e-tunes), with Berks kat and good mapping the car is so goooddd !