PPW(white) with Bronze Volk TE37(Pictures)
Thread Starter
Joined: May 2004
Posts: 2,330
Likes: 0
From: Charleston, SC
PPW(white) with Bronze Volk TE37(Pictures)
I ordered my wheels a month or so ago. I ordered them from Ryan(?) @350zforums.org, process was smooth, had some issues with my CC but we worked that out and got the rims out regardless.
19 inch Volk TE37
Front
8.5
+29 off set
Rear
9.5
+22 off set
Toyo T1
245/35
275/35
My Car with 17 inch 5zigen in hyper black...(found a curb in a rain storm... needed to replace my bent stock wheels with something that didnt cost 800 per wheel at that time)
My car with a front wheel installed complete with jack and tires comparing the new vs old:
Car is clean...relative to how it was...however:
from the front:
from the side for people who like to look at off sets and that stuff on the internet...I would rotate the image but as this is a mac I am current using, I dont know how to do that:
front again:
19 inch Volk TE37
Front
8.5
+29 off set
Rear
9.5
+22 off set
Toyo T1
245/35
275/35
My Car with 17 inch 5zigen in hyper black...(found a curb in a rain storm... needed to replace my bent stock wheels with something that didnt cost 800 per wheel at that time)
My car with a front wheel installed complete with jack and tires comparing the new vs old:
Car is clean...relative to how it was...however:
from the front:
from the side for people who like to look at off sets and that stuff on the internet...I would rotate the image but as this is a mac I am current using, I dont know how to do that:
front again:
Last edited by Ahsmo; Mar 23, 2005 at 10:58 AM.
Thread Starter
Joined: May 2004
Posts: 2,330
Likes: 0
From: Charleston, SC
I have a set of Tein S types...
I like the way the car looks but I wouldnt mind the drop. I would be out installing them right now but I lack the jack to get the job done as the floor jack I was using hardly fit before the drop.
In any case, there it is without my center caps which are on their way right now. Thanks Ryan(?).
Comments? How does it look?
Should I jack my car up and put 2x6s under the wheels and go ahead and put the teins on?
I like the way the car looks but I wouldnt mind the drop. I would be out installing them right now but I lack the jack to get the job done as the floor jack I was using hardly fit before the drop.
In any case, there it is without my center caps which are on their way right now. Thanks Ryan(?).
Comments? How does it look?
Should I jack my car up and put 2x6s under the wheels and go ahead and put the teins on?
Last edited by Ahsmo; Mar 23, 2005 at 10:55 AM.
Thread Starter
Joined: May 2004
Posts: 2,330
Likes: 0
From: Charleston, SC
Thanks guys 
They were in stock is the primary reason. I was a little bit worried about how it would look but it ended up looking better than expected.
Originally Posted by ssc
looks good, but why +29 in the front?...seems like most ppl go for +22 all around.
They were in stock is the primary reason. I was a little bit worried about how it would look but it ended up looking better than expected.
Trending Topics
Thread Starter
Joined: May 2004
Posts: 2,330
Likes: 0
From: Charleston, SC
well now that Im back in colorado, installing my springs may have to wait forever as I am selling my car..........
sad sad story, I need to start gathering parts to get this thing ready to sell
sad sad story, I need to start gathering parts to get this thing ready to sell
Registered User
Joined: May 2003
Posts: 69
Likes: 0
From: Schaumburg, IL
Looks GREAT! I actually have the same setup (PPW + Bronze TE37s).
Just be VERY VERY careful with these wheels . . . they have diamond cut lips and are anodized, not painted or powdercoated. If you curb one (or in my case, have Valet curb all 4), there is really nothing that can be done to repair them (without having them completely refinished a different color).
All you need now are some bronze Volk center caps . . . which I will most likely be parting with since I am having my wheels redone black. Let me know if you are interested - they are like new.
Just be VERY VERY careful with these wheels . . . they have diamond cut lips and are anodized, not painted or powdercoated. If you curb one (or in my case, have Valet curb all 4), there is really nothing that can be done to repair them (without having them completely refinished a different color).
All you need now are some bronze Volk center caps . . . which I will most likely be parting with since I am having my wheels redone black. Let me know if you are interested - they are like new.
Thread Starter
Joined: May 2004
Posts: 2,330
Likes: 0
From: Charleston, SC
Originally Posted by bigfatjeffk
Looks GREAT! I actually have the same setup (PPW + Bronze TE37s).
Just be VERY VERY careful with these wheels . . . they have diamond cut lips and are anodized, not painted or powdercoated. If you curb one (or in my case, have Valet curb all 4), there is really nothing that can be done to repair them (without having them completely refinished a different color).
All you need now are some bronze Volk center caps . . . which I will most likely be parting with since I am having my wheels redone black. Let me know if you are interested - they are like new.
Just be VERY VERY careful with these wheels . . . they have diamond cut lips and are anodized, not painted or powdercoated. If you curb one (or in my case, have Valet curb all 4), there is really nothing that can be done to repair them (without having them completely refinished a different color).
All you need now are some bronze Volk center caps . . . which I will most likely be parting with since I am having my wheels redone black. Let me know if you are interested - they are like new.
I was supposed to get them but only got 1, the other 3 are on there way. Thanks thou!
