BIG PROBLEM with my Axis Hiros...And a Question!
#24
Registered User
Join Date: Jan 2006
Location: pomona
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by eat rice z33
i wouldnt take hiros if you payed me to run them on my car. hell even a 5 mile and hour rim break can send you into oncoming traffic! i would turn around and throw those rims right in the garbage! but hey i geuss im the only one that does 100+ mph runs daily. BEst of luck to you and godspeed
even though I have axis wheels on my z, I am now concerned.
#25
Dr. Wired
iTrader: (2)
Originally Posted by Ed 718
Are you thinking of ditching your wheels Wired
I was talking about next time I buy rims in general... that's all. Like whenever I get another car (was thinking about buying used NSX when I get out of grad school).
Bubble: I have always loved the CPF tunes. And they're racing hart, not RH ;P
Last edited by Wired 24/7; 02-13-2006 at 02:36 PM.
#26
New Member
iTrader: (38)
I think the early Hiro's did that, I have had no problems with mine, I have been running then for a year... I will check them every now and then (nothing yet). Some people have problems, some don't, but im sure they will replace them, cause that's sure not your fault.
As for the CPF-Tune, if I could switch over without suffering too bad in the pocket I would, but them things are EXPENSIVE.
These are hot too... SSR Professor SP-1
As for the CPF-Tune, if I could switch over without suffering too bad in the pocket I would, but them things are EXPENSIVE.
These are hot too... SSR Professor SP-1
Last edited by MyV6IsFast3r; 02-13-2006 at 03:00 PM.
#27
Registered User
iTrader: (4)
Join Date: Sep 2004
Location: Savannah, GA
Posts: 572
Likes: 0
Received 0 Likes
on
0 Posts
Wow Richard that sucks
I think those rims look great on your car, I would just try to have them replaced. That is definitely some scary stuff. Let me know if you need anything
You know... you could always get some cash out of it and buy my Kazera's and I could get some Nismo's or SSR's... ok stop laughing at me... it was just a joke
Mike
I think those rims look great on your car, I would just try to have them replaced. That is definitely some scary stuff. Let me know if you need anything
You know... you could always get some cash out of it and buy my Kazera's and I could get some Nismo's or SSR's... ok stop laughing at me... it was just a joke
Mike
#28
Registered User
Join Date: Aug 2005
Location: santa fe springs
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Axis Hiros
please contact the merchant you purchase the wheels from or Axis Sport Tuning directly at 562-906-9898 or info@axiswheels.com. we will replace the wheel under warranty.
James Chen / Axis
James Chen / Axis
#29
Registered User
Join Date: Apr 2004
Location: Germantown, MD
Posts: 1,039
Likes: 0
Received 0 Likes
on
0 Posts
Damn, and someone said he didn't care
Originally Posted by james axis
please contact the merchant you purchase the wheels from or Axis Sport Tuning directly at 562-906-9898 or info@axiswheels.com. we will replace the wheel under warranty.
James Chen / Axis
James Chen / Axis
#30
Registered User
Thread Starter
Join Date: Jan 2003
Location: new orleans
Posts: 1,426
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by james axis
please contact the merchant you purchase the wheels from or Axis Sport Tuning directly at 562-906-9898 or info@axiswheels.com. we will replace the wheel under warranty.
James Chen / Axis
James Chen / Axis
Thank you very much for your response. In a previous post on this forum you mentioned that early shipments of Hiros were unknowingly produced from a bad batch of aluminum ingot. Bearing this in mind, my entire set of wheels is faulty, and will crack, sooner or later, (and whether or not I am aware) due to manufacturing defects. For safety concerns, I am seeking to replace the my wheels with a set produced at your new plant so as to alleviate my personal safety concerns about driving on a set of wheels which you have posted here were produced improperly.
To ensure the replacements are from your new production facility, would I do best to contact Axis directly?
#31
Dr. Wired
iTrader: (2)
Originally Posted by syf0n
James,
Thank you very much for your response. In a previous post on this forum you mentioned that early shipments of Hiros were unknowingly produced from a bad batch of aluminum ingot. Bearing this in mind, my entire set of wheels is faulty, and will crack, sooner or later, (and whether or not I am aware) due to manufacturing defects. For safety concerns, I am seeking to replace the my wheels with a set produced at your new plant so as to alleviate my personal safety concerns about driving on a set of wheels which you have posted here were produced improperly.
To ensure the replacements are from your new production facility, would I do best to contact Axis directly?
Thank you very much for your response. In a previous post on this forum you mentioned that early shipments of Hiros were unknowingly produced from a bad batch of aluminum ingot. Bearing this in mind, my entire set of wheels is faulty, and will crack, sooner or later, (and whether or not I am aware) due to manufacturing defects. For safety concerns, I am seeking to replace the my wheels with a set produced at your new plant so as to alleviate my personal safety concerns about driving on a set of wheels which you have posted here were produced improperly.
To ensure the replacements are from your new production facility, would I do best to contact Axis directly?
That's a big +1 . If one wheel was bad, what are the odds that the others AREN'T bad?
I'd guess pretty bad odds.
I hope they replace all 4 for you, man. Good luck.
#32
Registered User
Join Date: Aug 2005
Location: santa fe springs
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
please contact Darren or Steve at Axis Sport Tuning 562-906-9898 or steve or darren@axiswheels.com the faulty batch was only on the 19x8.5 size (front wheel for Z) the 19x9.5 or 10.5 are fine, we will gladly replace your 2 front wheel.
James
James
#33
BRAVEHEART
iTrader: (32)
Join Date: Feb 2004
Location: PRODUCT OF BROOKLYN 718 USA
Posts: 8,830
Likes: 0
Received 3 Likes
on
3 Posts
I was concerned about the cracking when I ordered my silver hiro's but now that I see you post James it shows me the president of the company cares about it's customers and that is a huge plus.
#37
Registered User
iTrader: (2)
Join Date: Feb 2004
Location: Concord, OH
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Ed 718
I was concerned about the cracking when I ordered my silver hiro's but now that I see you post James it shows me the president of the company cares about it's customers and that is a huge plus.
#38
Registered User
Thread Starter
Join Date: Jan 2003
Location: new orleans
Posts: 1,426
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by james axis
please contact Darren or Steve at Axis Sport Tuning 562-906-9898 or steve or darren@axiswheels.com the faulty batch was only on the 19x8.5 size (front wheel for Z) the 19x9.5 or 10.5 are fine, we will gladly replace your 2 front wheel.
James
James
I just had a satisfactory conversation with Darren on the matter of the replacement wheels. He is a great guy and an asset to your company. I sincerely appreciate your attention in this matter, and look forward to doing business with Axis again in the future when I purchase another set of wheels
Thanks again,
Richard Thompson