So 300hp track engine or 287hp engine, which one takes to mods better?
#21
Registered User
iTrader: (16)
Join Date: Mar 2004
Location: Nashville, TN
Posts: 2,939
Likes: 0
Received 0 Likes
on
0 Posts
300hp engine changes:
1)revised lower plenum design with shorter and fatter runners
2)more agressive cam profile
3)revised piston shape
4)stronger rod bolts (maybe stronger rods also)
5)variable cam timing on the intake and exhaust cams (287hp engine is only on intake cams)
6)higher 7000rpm redline
The 300hp engine also MIGHT have different heads. If I remeber correctly, they have a different part number then the 287hp heads. This could be for performance reason or just becuase of the added variable cam timing.
1)revised lower plenum design with shorter and fatter runners
2)more agressive cam profile
3)revised piston shape
4)stronger rod bolts (maybe stronger rods also)
5)variable cam timing on the intake and exhaust cams (287hp engine is only on intake cams)
6)higher 7000rpm redline
The 300hp engine also MIGHT have different heads. If I remeber correctly, they have a different part number then the 287hp heads. This could be for performance reason or just becuase of the added variable cam timing.
Last edited by thawk408; 10-26-2005 at 07:19 AM.
#22
Registered User
iTrader: (3)
Join Date: Mar 2005
Location: BayArea
Posts: 1,212
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by PureXTZ
What did you want to know, how variable cam timing works or the difference between the rev up motor vs. the 287 motor?
#25
New Member
iTrader: (1)
Join Date: Jun 2003
Location: Wild Wild West
Posts: 3,096
Likes: 0
Received 0 Likes
on
0 Posts
Everyone is talking HP. Nobody is talkin' bout the loss in TQ in the rev-up engine. Not to mention if these mods are bringing the TQ number back up.
Again..someone posted that the 06 weigh more..which is absolutely true
Again..someone posted that the 06 weigh more..which is absolutely true
#26
Registered User
iTrader: (3)
Join Date: Mar 2005
Location: BayArea
Posts: 1,212
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by NissanZfan
What is the difference between intake cam timing and variable timing to the exhaust cams. Why use one oppose to the other on the rev up motor?
But still no answer.
#27
Registered User
iTrader: (3)
Join Date: Mar 2005
Location: BayArea
Posts: 1,212
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rockinbboy
Everyone is talking HP. Nobody is talkin' bout the loss in TQ in the rev-up engine. Not to mention if these mods are bringing the TQ number back up.
Again..someone posted that the 06 weigh more..which is absolutely true
Again..someone posted that the 06 weigh more..which is absolutely true
You are missing the point of the thread, the original question was what takes better to mods, not what one is faster, then i somewhat hijacked the thread with my question.
Last edited by NissanZfan; 10-26-2005 at 10:51 PM.
#28
Registered User
iTrader: (1)
Join Date: Oct 2005
Location: Las Vegas
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Takes more mods is 287.
Performs better with mods is 300.
I had the same basic mods on both my old 287 and current 300. The little difference I saw came from the 300 over the 287. Now that I have fully decked out my 300, I am extremely happy with it. Of course I went the expensive route with all Nismo.
Performs better with mods is 300.
I had the same basic mods on both my old 287 and current 300. The little difference I saw came from the 300 over the 287. Now that I have fully decked out my 300, I am extremely happy with it. Of course I went the expensive route with all Nismo.
#29
Guest
Posts: n/a
Originally Posted by NissanZfan
You are missing the point of the thread, the original question was what takes better to mods, not what one is faster, then i somewhat hijacked the thread with my question.
the answer to your original question is the 300hp
#30
Registered User
iTrader: (3)
Join Date: Mar 2005
Location: BayArea
Posts: 1,212
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mc350z
the answer to your original question is the 300hp
#31
Guest
Posts: n/a
Originally Posted by NissanZfan
You seem to be knowledgeable........What is the difference between intake cam timing and variable timing to the exhaust cams. Why use one oppose to the other on the rev up motor?
yeah i guess im pretty knowledgeable but not when it comes to real technical stuff like that
all i know is the rev up uses both where the 03 uses just the intake timing not exaust and because of this seems the rev up can move air in/out better
accordint to some dyno charts posted on here the rev up pulls more evenly to redline
and the hp torque curves are more smooth across the board where the 287 motor drops off rapidly after a certain RPM
thats about the depth of my knowledge about the two
Last edited by **; 10-26-2005 at 11:46 PM.
#32
Guest
Posts: n/a
also i think the lower plenum is difference really plays a role in the rev up performance in the higher RPM range. there was a thread on here about buying the redesigned plenum part for gains, but i think it was jason that said it would be more benificial to have a ECU reflash with a higher redline to get the full effect.
so IMO it seems all these changes would be very friendly to mods especailly those that helped the motor breathe better
so IMO it seems all these changes would be very friendly to mods especailly those that helped the motor breathe better
Last edited by **; 10-26-2005 at 11:50 PM.
#33
Registered User
iTrader: (16)
Join Date: Mar 2004
Location: Nashville, TN
Posts: 2,939
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by NissanZfan
You seem to be knowledgeable........What is the difference between intake cam timing and variable timing to the exhaust cams. Why use one oppose to the other on the rev up motor?
#34
Sponsor
Performance Nissan
Performance Nissan
iTrader: (92)
Join Date: Dec 2004
Location: Pasadena/Bay Area
Posts: 6,151
Likes: 0
Received 0 Likes
on
0 Posts
Piston engines normally use poppet valves for intake and exhaust. These are driven (directly or indirectly) by cams on a camshaft. The cams open the valves (lift) for a certain amount of time (duration) during each intake and exhaust cycle. The timing of the valve opening and closing is also important. The camshaft is driven by the crankshaft through timing belts, gears or chains.
The profile of these cams is optimized for a certain engine rpm, and this tradeoff normally limits low-end torque or high-end power. VVT allows the cam profile to change, which results in greater efficiency and power.
At high engine speeds, an engine requires large amounts of air. However, the intake valves may close before all the air has been given a chance to flow in, reducing performance.
On the other hand, if the cam keeps the valves open for longer periods of time, like with a racing cam, problems start to occur at the lower engine speeds. This will cause unburnt fuel to exit the engine since the valves are still open. This leads to lower engine performance and increased emissions.
The profile of these cams is optimized for a certain engine rpm, and this tradeoff normally limits low-end torque or high-end power. VVT allows the cam profile to change, which results in greater efficiency and power.
At high engine speeds, an engine requires large amounts of air. However, the intake valves may close before all the air has been given a chance to flow in, reducing performance.
On the other hand, if the cam keeps the valves open for longer periods of time, like with a racing cam, problems start to occur at the lower engine speeds. This will cause unburnt fuel to exit the engine since the valves are still open. This leads to lower engine performance and increased emissions.
#36
New Member
iTrader: (4)
Yea, thats right. Valve timing controls exactly that, the time the valves stays open or closed (in the case of the 300s). Intake wise, concerning all of the 287 Zs, the CVTCS (continuous variable valve timing control system) allows for better fuel economy while also allowing for, essentially, more power at great throttle lengths. All this is done by adjusting the valves for either more air and conservation of air/fuel.
On the exhaust side (300s) the CVTCS follows in conjunction with the intake valve timing. It adjusts the valves on the exhaust side to let more exhaust out faster or slower depending on the driving style/throttle position. This, in turn, allows for more power simply because the exhaust is getting out quicker and more..."smartly".
In all, nissans CVTCS is a never-ending VTEC with all the up's of VTEC and without any of the down's of VTEC.
So which is better for mods? I'd have to say the 300's. But considering the decreased torque, heavier weight, and any other factors, I would rather mod an 05 Base with the 287. Or maybe im just biased because I have exactly that. I dunno.
On the exhaust side (300s) the CVTCS follows in conjunction with the intake valve timing. It adjusts the valves on the exhaust side to let more exhaust out faster or slower depending on the driving style/throttle position. This, in turn, allows for more power simply because the exhaust is getting out quicker and more..."smartly".
In all, nissans CVTCS is a never-ending VTEC with all the up's of VTEC and without any of the down's of VTEC.
So which is better for mods? I'd have to say the 300's. But considering the decreased torque, heavier weight, and any other factors, I would rather mod an 05 Base with the 287. Or maybe im just biased because I have exactly that. I dunno.
#37
Registered User
iTrader: (3)
Join Date: Jan 2005
Location: AZ
Posts: 90
Likes: 0
Received 0 Likes
on
0 Posts
which Z
Originally Posted by nitrouz
proven. 300hp engine. mod for mod, the 300hp engine will produce more power due to the variable timing of intake and exhaust as mc350z said.
#38
Registered User
Join Date: Apr 2005
Location: Scottsdale, AZ
Posts: 548
Likes: 0
Received 0 Likes
on
0 Posts
I think if this Motordyne mod for the Rev-Up motors pans out, it will be a no brainer.
If a simple mod can restore the lost TQ of the rev-up motor and increase hp over the range, then there is no downside for rev-up'ng
If a simple mod can restore the lost TQ of the rev-up motor and increase hp over the range, then there is no downside for rev-up'ng
#39
Sponsor
Performance Nissan
Performance Nissan
iTrader: (92)
Join Date: Dec 2004
Location: Pasadena/Bay Area
Posts: 6,151
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by nizmoz
Guys, I have a 2004 Z with NISMO Cams. I think (not sure) that the NISMO Cams do provide variable intake and exhaust timing. Anyone know if this is true, and how it compares to the 300bhp motor?
#40
Registered User
iTrader: (2)
Join Date: Nov 2003
Location: Houston
Posts: 1,523
Likes: 0
Received 0 Likes
on
0 Posts
Whatever the difference is, I'm sure the one with the better driver will win.
I think the difference goes out the door once you Turbo it.
Even if you Turbo and the 300hp one makes 20 more hp, it's still a driver's race.
I think the difference goes out the door once you Turbo it.
Even if you Turbo and the 300hp one makes 20 more hp, it's still a driver's race.
Thread
Thread Starter
Forum
Replies
Last Post
liqalu04
Engine & Drivetrain
31
01-02-2022 12:58 PM
Tochigi_236
Feedback & Suggestions for Our Forum
8
09-27-2015 03:40 PM