W3 to W6 Upgrade *Sold*
#1
Registered User
Thread Starter
iTrader: (3)
Join Date: Jun 2006
Location: Jackson. MS
Posts: 191
Likes: 0
Received 0 Likes
on
0 Posts
W3 to W6 Upgrade *Sold*
Guys, I decided to get 2 W6s instead of the 2 W3s i was going to. I have a USED JL 500/1 in MINT condition. Works great, not scraches.
[EDIT]
I was going to post it on ebay, But here is the Info
JL 500/1
Condition: USED (4 Months) Look like New (No Scraches)
Key Features :
# Rated Power: 500 W RMS @ 1.5W-4W (11V-14.5V)
# THD at Rated Power: <0.05%
# S/N Ratio: >95dB below rated power
# (A-weighted,20-20KHz noise bandwidth)
# Frequency Response: 5 Hz - 500 Hz (+0,-1dB)
# Damping Factor: >500 @ 4W/50 Hz,>250 @ 2W/50 Hz
# Input Range: switchable from 200mV-2V RMS
# to 800mV-8V RMS
# Dimensions: 13.4"L x 9.25"W x 2.36"H
# Features:
# Differential-Balanced Input Topology: (1 pair of inputs)
# ON-board crossover:fully adjustable (40-200 hz)selectable slope (12 db or 24 db per octave)
# Preamp Output: 2-channel (independent active filter, parallel with amp filter or full-range)
# Bass EQ: parametric with variable boost up to 15dB and Remote Bass Option.
# Infrasonic Filter: fully-variable 24dB/octave from 15-60 Hz
# Signal-Sensing Turn-On: permits operation without remote lead
# Dual mono speaker output connections: accept up to 8ga.wire
# +12V and Ground connections: accept up to 4ga.wire
SOLD
[EDIT]
I was going to post it on ebay, But here is the Info
JL 500/1
Condition: USED (4 Months) Look like New (No Scraches)
Key Features :
# Rated Power: 500 W RMS @ 1.5W-4W (11V-14.5V)
# THD at Rated Power: <0.05%
# S/N Ratio: >95dB below rated power
# (A-weighted,20-20KHz noise bandwidth)
# Frequency Response: 5 Hz - 500 Hz (+0,-1dB)
# Damping Factor: >500 @ 4W/50 Hz,>250 @ 2W/50 Hz
# Input Range: switchable from 200mV-2V RMS
# to 800mV-8V RMS
# Dimensions: 13.4"L x 9.25"W x 2.36"H
# Features:
# Differential-Balanced Input Topology: (1 pair of inputs)
# ON-board crossover:fully adjustable (40-200 hz)selectable slope (12 db or 24 db per octave)
# Preamp Output: 2-channel (independent active filter, parallel with amp filter or full-range)
# Bass EQ: parametric with variable boost up to 15dB and Remote Bass Option.
# Infrasonic Filter: fully-variable 24dB/octave from 15-60 Hz
# Signal-Sensing Turn-On: permits operation without remote lead
# Dual mono speaker output connections: accept up to 8ga.wire
# +12V and Ground connections: accept up to 4ga.wire
SOLD
Last edited by maturola; 07-21-2006 at 08:36 AM. Reason: Rules*
Thread
Thread Starter
Forum
Replies
Last Post
350Z Project X
Suspension
9
10-10-2015 09:23 AM