350Z How to's
#61
Registered User
Join Date: Feb 2003
Location: Alabama
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
Roadster Rear Speaker Removal
The Roadster is more tricky than the coupe to take out the rear speakers. You have to take apart the rollbar covers. Nissan in their infinate wisdom made the covers for the rollbars disposable. According to the manuel it shoes an X by the rollbar covers, which means these items are destroyed after taken apart. I took mine apart last night, and I was able to get them apart with only breaking one piece. The trick is to use a long screwdriver and try to seperate the pieces from under neath (inside the covers). The clips from the front cover are male and the back cover are female. The male clips have a locking clip that is facing down. If you push up on the clip, you can manage to romove the covers without breaking the clips.
With this Disposable rollbar cover, It is a good thing that Nissan put such a wonderful stereo in our cars so we don't have to worry about replacement. I hope the future models they actaully upgrade the Stereo even futher by putting in Jenson.
With this Disposable rollbar cover, It is a good thing that Nissan put such a wonderful stereo in our cars so we don't have to worry about replacement. I hope the future models they actaully upgrade the Stereo even futher by putting in Jenson.
#63
Registered User
Join Date: Nov 2004
Location: Hurst, TX
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
350x factory radio wiring diagram
I replaced the factory speakers fron and rear with Polk Momo coax in the rear and Polk Momo separates in the front. I've added a Polk Momo 300.2 amp under the passenger seat. I've run rca's and speaker wire from the amp up to the radio. I ran 4 guage wire from the battery to the amp and graounded the amp to a bolt on the passenger side of the car. Now I need to know which wires to cut an splice for the fron speakers. I've looked on the web and on this site but can't find the needed information. Does anyone know which wires I'm needing to use? I also need to hookup the amps remote wire.
Thanks,
Mark Matthews
Thanks,
Mark Matthews
#65
Registered User
iTrader: (7)
The How-to on the center dash is very detailed but it is on a car with no OEM Nav. Does anyone have any help for us that do have OEM nav and need to take the denter console off?
It's not as easy as someone said to pull on the navigation button faceplate and it will pop out. The Stock navigation faceplate looks to be one piece.
It's not as easy as someone said to pull on the navigation button faceplate and it will pop out. The Stock navigation faceplate looks to be one piece.
#66
Registered User
iTrader: (7)
Um, nevermind, I read the service manual and did what they said to do. get two flathead screwdriver, tape them up(as not to scratch the panels). Make sure one is big and the other one is a small flathead so you can fit it into the cracks.
1. Insert the smaller screwdriver wrapped with tape into the center square hole for the cluster lid D pawl. Bend cluster lid D backwardto create a front/back gap.
2. Insert another tapped screwdriver into the gap that step number 1 made and start to careful pry.
See below for pictures, hope this helps people who are in my situation.
1. Insert the smaller screwdriver wrapped with tape into the center square hole for the cluster lid D pawl. Bend cluster lid D backwardto create a front/back gap.
2. Insert another tapped screwdriver into the gap that step number 1 made and start to careful pry.
See below for pictures, hope this helps people who are in my situation.
Last edited by ZlleH; 10-19-2005 at 07:23 PM.
#68
Registered User
iTrader: (50)
Join Date: Jun 2005
Location: Indiana
Posts: 4,266
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by srmd22
question: If you wire a detector into the homelink, will it power on and off with the car? And do you need any additional connections to the fusebox?
#71
Registered User
Join Date: Aug 2006
Location: Atlanta, GA
Posts: 613
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys, Take it easy on me,,for I just found this awesome website, joined and now I have a question? Could someone please post a "how-to" to take apart the dash to remove stock/install aftermarket head-unit? I saw a thread in first post,,,but for some reason, it is not opening on my computer..All other listed how-to's open just fine....Please help......Any would be greatly appreciated.....thanks.
#76
Registered User
Join Date: Sep 2006
Location: Memphis, TN
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Does anyone know how to disassemble the door panels on an '06 Z Coupe? Everything I've seen has a different driver's side door panel and a different center console than mine.
#77
Registered User
Join Date: Sep 2006
Location: Chicago, Illinois
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
06 removal of Bose Stereo?...
I have an 06 Grand Touring Convertible. I need to know how to take apart the dash so i can remove the Bose system and install a navigation unit. I click on the links that may be of some help, but none seem to work properly. I would appreciate anyones help. Thankyou
#78
Registered User
iTrader: (27)
Join Date: Jun 2006
Location: Lafayette, LA
Posts: 5,397
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by tonkadog
How to remove the door panels
https://my350z.com/forum/showthread....&threadid=7995
https://my350z.com/forum/showthread....&threadid=7995
#79
Registered User
iTrader: (11)
Join Date: Oct 2006
Location: Burbank, CA
Posts: 631
Likes: 0
Received 0 Likes
on
0 Posts
how do u install an aftermarket shift light. its the raptor shift light, i had it on a spec-v but that got ran over so i want to install it on this car for when i go to the track. helps out alot when u have a big *** helmet on ur head. so, any how to's on a shift light install?
#80
Registered User
iTrader: (24)
Join Date: Aug 2005
Location: NewCastle, WA
Posts: 2,947
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 918 Z
how do u install an aftermarket shift light. its the raptor shift light, i had it on a spec-v but that got ran over so i want to install it on this car for when i go to the track. helps out alot when u have a big *** helmet on ur head. so, any how to's on a shift light install?
-Peter