Need .25" Spacers and Studs for AutoX
#22
Registered User
iTrader: (49)
ARP studs are cheaper and stronger than NISMO. Custom order though...
for spacers call up Eibach and speak to Adam, they're getting a shipment in any day now 951.256.8300 www.eibach.com
for spacers call up Eibach and speak to Adam, they're getting a shipment in any day now 951.256.8300 www.eibach.com
#23
Registered User
iTrader: (4)
Originally Posted by 03Z33
ARP studs are cheaper and stronger than NISMO. Custom order though...
for spacers call up Eibach and speak to Adam, they're getting a shipment in any day now 951.256.8300 www.eibach.com
for spacers call up Eibach and speak to Adam, they're getting a shipment in any day now 951.256.8300 www.eibach.com
#24
Registered User
iTrader: (49)
www.arp-bolts.com
they don't have a part # for the 350Z studs yet, but it's very similar to another off-the shelf application. If you want longer ones, it's custom order. It usually works out to ~ $2-$5 per stud. I got a complete set on a group buy for my Nissan 240 for $45 (68mm length) but the knurl and thread pitch for the Z are different.
they don't have a part # for the 350Z studs yet, but it's very similar to another off-the shelf application. If you want longer ones, it's custom order. It usually works out to ~ $2-$5 per stud. I got a complete set on a group buy for my Nissan 240 for $45 (68mm length) but the knurl and thread pitch for the Z are different.
#33
Sponsor
Forged Performance
Forged Performance
iTrader: (92)
Hi everyone. I was contacted about sponsoring a "special purchase" of custom ARP wheel studs for the 350Z. ARP doesnt permit group buys, so this is NOT a GB.
That said, I need to gather a little more information before contacting ARP with this order.
I imagine that some members are going to want stock lengths, and other would prefer longer length studs. Is this correct?
The challenge with doing a custom order, is they typically want $2000 minimum purchase for custom orders, and thats a LOT of wheel studs.
And if people are requesting different lengths, this might not be possible.
Longer studs, seem only suitable for those using wheel spacers, and I have heard that stock Nissan studs are too short to be certified for true road race use/track days.
Anyone have anymore feedback on this?
That said, I need to gather a little more information before contacting ARP with this order.
I imagine that some members are going to want stock lengths, and other would prefer longer length studs. Is this correct?
The challenge with doing a custom order, is they typically want $2000 minimum purchase for custom orders, and thats a LOT of wheel studs.
And if people are requesting different lengths, this might not be possible.
Longer studs, seem only suitable for those using wheel spacers, and I have heard that stock Nissan studs are too short to be certified for true road race use/track days.
Anyone have anymore feedback on this?
#34
the burninator
iTrader: (11)
so is a good setup to use the H&R 5mm spacer with 50mm nismo hub bolts?
I currently have the H&R 5mm spacers, but not on yet. So the bolts they come with aren't good enough to use and I should go with the longer 50mm nismo bolts?
I currently have the H&R 5mm spacers, but not on yet. So the bolts they come with aren't good enough to use and I should go with the longer 50mm nismo bolts?
Last edited by sentry65; 03-23-2006 at 08:32 AM.
#35
Registered User
iTrader: (4)
Originally Posted by Sharif@Forged
Hi everyone. I was contacted about sponsoring a "special purchase" of custom ARP wheel studs for the 350Z. ARP doesnt permit group buys, so this is NOT a GB.
That said, I need to gather a little more information before contacting ARP with this order.
I imagine that some members are going to want stock lengths, and other would prefer longer length studs. Is this correct?
The challenge with doing a custom order, is they typically want $2000 minimum purchase for custom orders, and thats a LOT of wheel studs.
And if people are requesting different lengths, this might not be possible.
Longer studs, seem only suitable for those using wheel spacers, and I have heard that stock Nissan studs are too short to be certified for true road race use/track days.
Anyone have anymore feedback on this?
That said, I need to gather a little more information before contacting ARP with this order.
I imagine that some members are going to want stock lengths, and other would prefer longer length studs. Is this correct?
The challenge with doing a custom order, is they typically want $2000 minimum purchase for custom orders, and thats a LOT of wheel studs.
And if people are requesting different lengths, this might not be possible.
Longer studs, seem only suitable for those using wheel spacers, and I have heard that stock Nissan studs are too short to be certified for true road race use/track days.
Anyone have anymore feedback on this?
Thread
Thread Starter
Forum
Replies
Last Post
Colombo
Forced Induction
35
11-09-2020 10:27 AM