Stillen Swaybar Owners: Does your swaybar shift to the side too?
#1
Stillen Swaybar Owners: Does your swaybar shift to the side too?
Hey guys, well I recently noticed that my sway bar has a considerable amount of play in between the collars and the bushings/brackets..... it will shift roughly 3/4 of an inch left/right.. I tried to clamp the collars with some wormdrive clamps today to see if it will help, but I dont understand why it is doing this.. recently I did upgrade to polyurethane bushings, perhaps they are not as wide as the OEM bushings? I dont understand... The collars on the swaybars are welded so they didnt get moved.
Heres a pic:
Heres a pic:
#4
Registered User
iTrader: (17)
Join Date: Jun 2004
Location: San Diego
Posts: 2,039
Likes: 0
Received 0 Likes
on
0 Posts
Stillen added those welded collars because their sway bars used to slide much further to the side... the collar stops this. I have the hotchkis bars from before they came with collars welded on and I bought a set of collars that I bolted onto the bars to stop the movement. If you search there is a thread on the mcmaster-carr collar mod for the old style bars. I guess the movement is "normal."
Last edited by BlackSpec02; 03-14-2009 at 04:38 PM.
#5
i see.... it causes my endlinks to shift from || to be like \\ and //.. pretty annoying. Yea I wish the bar didnt bend directly after the bushing/bracket, otherwise I think I would put collars on the outsides of the bushing as well. Or a very skinny one to put inbetween the existing collar and the bushing.
#6
Ooo I found the thread... I think I shall order 2 of those clamps since they are pretty thin ( 9/16" wide ), so hopefully they will fit on the outsides of the bushing. Thanks for the tip!
Heres link to the part for the front sway bar
http://www.mcmaster.com/#6436k146/=wqrzr
Heres link to the part for the front sway bar
http://www.mcmaster.com/#6436k146/=wqrzr
Trending Topics
#8
Hmm well I got the clamps... unfortunately they dont work as well as I had hoped because of the curviture of the sway bar. I was hoping to put the clamps on the outsides of the bushings/bracket but the swaybar beings to curve right after so the clamp doesnt fit no there squarely... I had to just put the clamp along the curve of the swaybar so one edge of it is near the bushing, hopefully eliminating travel... Also I put worm drive clamps on the inside collars to prevent movement as well....
#9
Registered User
Join Date: Aug 2008
Location: Dayton Ohio
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
My Hotchkis sway bar had the same issue, and I bought some 1.25" PVC 40 conduit, cut two 1/4" pieces, then cut a slit in them so they would snap over the sway bar, and then snapped them in place between the welded collar on the sway bar and the poly sway bar bushing. They've been there for 6 months now and keep the sway bar from moving. PVC 80 would be thicker, and probably would work a little better.
#11
So I did the PVC spacer today, seems like it will work nicely. I bought some 1" pvc pipe couplings, so the ID was about 1.25", only costs $.55 I believe... cheap. Too bad I wasted $20 bucks on those mcmaster clamps my fault tho.
Thanks again.
Thanks again.
Last edited by jining; 03-16-2009 at 06:34 PM.
#13
Registered User
Join Date: Nov 2005
Location: Inland Empire
Posts: 204
Likes: 0
Received 0 Likes
on
0 Posts
I'd like to state that that is how my problem started in the first place by upgrading the stock bar with urethane bushings......then I upgraded to hotchkis sways to solve the problem ending up right where I was in the first place....I am going to try the PVC fix.
I believe the stock rubber bushings actually grip the bar in a way that it does not slide around....the urethane bushings slop around due to the grease that comes with it.
I believe the stock rubber bushings actually grip the bar in a way that it does not slide around....the urethane bushings slop around due to the grease that comes with it.
Last edited by danimaldaisy; 04-13-2009 at 03:23 PM.
#14
New Member
iTrader: (5)
Join Date: Nov 2003
Location: LA
Posts: 519
Likes: 0
Received 0 Likes
on
0 Posts
You did the right thing danimal-manimal! LOL Loved that show! The Prothane bushings are a good mod as the stock ones ARE rubber. If you grease them well, def a worthy replacement for teh OEMs.
As for the sways, a few of the first sets of bars from several companies didn't have collars, a mistake maybe? I have the older, gold colored Stillen bars with welded collars and that's why I bought them.
As for the sways, a few of the first sets of bars from several companies didn't have collars, a mistake maybe? I have the older, gold colored Stillen bars with welded collars and that's why I bought them.
#16
Well, even the stillen sways with the collars are prone to the slipping. Mine are the red ones with collars. Luckily, the PVC mod worked for me as well. I agree with danimal and think the stock rubber bushings must have gripped the bar, where as the urethane ones do not and slide around.
#17
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
#20
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
The endlinks have plenty of room for movement. The only part that really hurts the endlinks is the stiffer bar. The stiffer the settings , the faster the endlinks wear out.