Shop says "Tension Rods Are Worn Out" ???
#1
Shop says "Tension Rods Are Worn Out" ???
Went in for an oil change and the shop owner tells me my Tension Rods are worn out and will cause the alignment to go out/camber wear on tires/etc. and it will cost $675 to fix...
I have a couple questions for you guys...
1. Is the part actually called a Tension Rod or is it commonly referred to something else? Searches are not coming up with many results, possibly Compression Rod??
2. Does the entire ARM get worn out, or is it just the bushing?
As always, thanks in advance
-Chris
I have a couple questions for you guys...
1. Is the part actually called a Tension Rod or is it commonly referred to something else? Searches are not coming up with many results, possibly Compression Rod??
2. Does the entire ARM get worn out, or is it just the bushing?
As always, thanks in advance
-Chris
#2
Registered User
iTrader: (9)
1. These rods on the Z33 are referred to as "Compression Rods" and are part of a new design by Nissan made specifically for the Z33 to split the lower link into 2 peices thereby creating 2 seperate pivot points at 2 seperate ball joints.
On the Z32, however, a similar part was referred to as the "tension rods".
2. No, the entire arm cannot get warn out as it is a soild peice of aluminum. The part on this arm that CAN get warn out is the ball joint on the lower end of the rod, or the end of the rod that is closest to the wheel. Or the upper "flex" joint located furthest from the wheel as well.
The joint, itself, cannot be replaced without replacing the entire rod.
EDIT: I would inspect, yourself, before getting this part replaced.
Also, make sure they are seeing the ball joint, itself, as being bad and not the lower rubber seat that the ball joint's bolt end sits in.
On the Z32, however, a similar part was referred to as the "tension rods".
2. No, the entire arm cannot get warn out as it is a soild peice of aluminum. The part on this arm that CAN get warn out is the ball joint on the lower end of the rod, or the end of the rod that is closest to the wheel. Or the upper "flex" joint located furthest from the wheel as well.
The joint, itself, cannot be replaced without replacing the entire rod.
EDIT: I would inspect, yourself, before getting this part replaced.
Also, make sure they are seeing the ball joint, itself, as being bad and not the lower rubber seat that the ball joint's bolt end sits in.
Last edited by GeauxLadyZ; 10-12-2009 at 07:14 AM.
#3
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
#4
Registered User
iTrader: (9)
Joint is avaliable without the arm w/ Infinity?
I think the inner bushing is avaliable seperate, only, not the outer ball joint. And its prob only avaliable seperate because G35 initially had problems with the original inner bushings, so they offered cheap fix.
Last edited by GeauxLadyZ; 10-12-2009 at 07:21 AM.
Trending Topics
#8
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
The inner bushing is normally the part that fails.
#10
Registered User
Join Date: Jun 2007
Location: California
Posts: 41
Likes: 0
Received 0 Likes
on
0 Posts
I have the same problem too bro. So the only thing that would solve this is to buy the front lower compression rod which includes the ball joint and bushing. =X
#11
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
Guess you didn't read much , if its just the inner bushings that are bad, you can get them from infinity. The Chance of the arms actually being bad is slim, they only reason to replace the arms is if the ball joint is bad or you bent the arm.
#14
Registered User
Join Date: Jun 2007
Location: California
Posts: 41
Likes: 0
Received 0 Likes
on
0 Posts
It was the ball joint's rubber cover. I'm thinking maybe that's why there was a lot of grease everywhere. Which sends me to have to buy the whole compression rod yea? =[ ]
Last edited by gelochi; 10-14-2009 at 08:32 AM.
#15
Former Sponsor
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
if the boot is torn and the grease is coming out, it's a matter of time before it gets worse. I don't know of any replacement ball joints yet (haven't really look into it because it's not a common thing)
#16
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
My beater truck just got a new tie rod end boot about a year ago, the boot has been bad since about 01, that truck been mudding and everything else and the joint still didn't fail. Its not worth the cost to replace the joint till it fails.
#17
Registered User
iTrader: (9)
^ Labor hours will cost the same as replacing, but you will save on part cost.
Personally, i would replace te entire arm.....its not that expensive for the arm, and can you be sure of the amount of time you have been driving on it with the torn cover?
http://www.courtesyparts.com/54468n-...tml?cPath=714&
For 138 buck, you get new rod, new inner bushing, new balljoint w/cover and new rubber ball joint seat....why not.
I baby my car like that, though.
Personally, i would replace te entire arm.....its not that expensive for the arm, and can you be sure of the amount of time you have been driving on it with the torn cover?
http://www.courtesyparts.com/54468n-...tml?cPath=714&
For 138 buck, you get new rod, new inner bushing, new balljoint w/cover and new rubber ball joint seat....why not.
I baby my car like that, though.
Last edited by GeauxLadyZ; 10-14-2009 at 01:10 PM.
#18
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
^ Labor hours will cost the same as replacing, but you will save on part cost.
Personally, i would replace te entire arm.....its not that expensive for the arm, and can you be sure of the amount of time you have been driving on it with the torn cover?
http://www.courtesyparts.com/54468n-...tml?cPath=714&
For 138 buck, you get new rod, new inner bushing, new balljoint w/cover and new rubber ball joint seat....why not.
I baby my car like that, though.
Personally, i would replace te entire arm.....its not that expensive for the arm, and can you be sure of the amount of time you have been driving on it with the torn cover?
http://www.courtesyparts.com/54468n-...tml?cPath=714&
For 138 buck, you get new rod, new inner bushing, new balljoint w/cover and new rubber ball joint seat....why not.
I baby my car like that, though.
#20
...
It sounds like I could probably do this on my own... I never had the time to make it to the shop again but this weekend the wheels are coming off and I'm going to inspect the bushings and joints to see specifically what the real problem is... I will post pics to get a second opinion...
I have another question... If my joint/bushings/both need to be replaced, would it be stupid to get an alignment before correcting the problem? Could these faulty parts cause a premature misalignment or do they have no bearing on the camber and toe settings???
From reading and researching it sounds like these parts can cause wear during braking (only???)
Thanks in advance...
I have another question... If my joint/bushings/both need to be replaced, would it be stupid to get an alignment before correcting the problem? Could these faulty parts cause a premature misalignment or do they have no bearing on the camber and toe settings???
From reading and researching it sounds like these parts can cause wear during braking (only???)
Thanks in advance...