Has anyone really pulled 300rwhp yet on a N/A VQ? If not, what is the highest number pulled thus far? Personally, I cannot remember anyone having a real 300+ rwhp N/A pull.

Lets talk about it. Post your best dyno pull and compare mods.

 

I think Rickdogg is pretty close...I think he's somewhere around 296 or so?

 

Andy from performance nissan has 292whp on a REVUP motor with no cams.

 

292 without cams is impressive. I pulled a 282hp/282tq without them which pleasantly shocked me. Since then, I have added a plenum spacer thus not sure what it would pull now.

 

I might have to re-dyno with my new coil system that I put on after the last dyno session to see if I can eclipse that 300 mark. Also, if I could get a velocity stack built for my ARC intake it would push it over

https://my350z.com/forum/engine-and-drivetrain/166361-dyno-results-from-tuning-with-technosquare-and-motordyne.html

 

I have got around 285 rwHP (around 348 engine HP) on Australian dyno machine with...

11.5:1 forged pistons
Carrillo rods
Ferrea Valve Train set
Cylinder Heads works + ported/polish
Nismo Spec 1 cams
Nismo VTC units
MoTeC M600
Nismo flywheel
Full exhaust system from headers
Modified intake system
05 lower plenum with MD spacer
UR pulley
and more...

cheers,

richie

 

I think you should be around the 320 rwhp or so

 

not too sure about that though... might be somewhere around there if the car was run in the States...

richie

 

I'd like to see 300whp, documented via a dynojet graph, SAE, with a bone stock Z as a baseline from the same shop if possible. If the baseline is showing 230ish... I say that car is making some decent power. I think Doug at Crawford is the closest I've seen in America at 290ish with headwork, big cams, piggyback, but I'd bet money that z350zlover in Austrailia is making over 300whp with his spec 1 and motec, but again I wanna see it on a dynojet, so he doesnt count. When's the next so Cal dyno day?

 

I know a guy... who pulled more than 300whp...

... on a Nitrously Aspirated VQ.

 

Mjedens did a long while ago, now he just pulled 730whp on his monster SGP-built motor-greddy twin turbo setup. Talk about a pioneer.

 

https://my350z.com/forum/engine-and-drivetrain/165068-who-said-it-can-t-be-done.html

 

Your not serious are you? That is probably the least credible thread I have read in awhile.

 

Do you know what type of dyno he pulled it on?

 

+1 mjedens was so far ahead of everyone to 300whp that hardly any of the members that were around at that time are still around to remind everyone plus he did it without a EU, Motec, HKS, UTEC, Unichip etc...

 

Do you know what type of dyno he pulled it on?

 

Crazy server slow-down caused double post

 

i think Dynojet because motordyne was testing the MREV on one of the threads and they also mentioned andy was there.

 

1. Sorry guys for the multiple posts. The server was lagging so much that when I clicked to reply, it did nothing but in reality it did send the reply.

2. Keep up the feedback regarding who is pulling the most. We are in the 4th year of production on the 350Z thus we have had ample time to figure out how to get some good numbers for N/A motors.

3. Is there anyone else pulling 290rwhp +?

 

I heard that Mjedens didn't actually have 300hp. Just a rumor though.