Notices
Engine & Drivetrain VQ Power and Delivery

Engine suddenly won't run above 2,500 RPM

Thread Tools
 
Search this Thread
 
Old Jul 25, 2009 | 10:39 AM
  #1  
awZum's Avatar
awZum
Thread Starter
Registered User
 
Joined: Jul 2009
Posts: 1
Likes: 0
From: So California
Unhappy Engine suddenly won't run above 2,500 RPM

I have a 2004 with 13,900 miles. Yesterday went to start it and it
struggled to start. The idle was fluctuating, all of the dash lights were on
and when I increadsed the throttle it ran rough at 2,500.
It even smelled a little funny when hot.

ECU bad?

Thanks
Reply
Old Jul 25, 2009 | 12:08 PM
  #2  
s31t8n8's Avatar
s31t8n8
New Member
iTrader: (12)
 
Joined: Jun 2006
Posts: 1,383
Likes: 1
From: Piscataway, NJ
Default

did you install anything on your car and did you try to start it again?
Reply
Old Jul 25, 2009 | 07:36 PM
  #3  
gabe3d's Avatar
gabe3d
New Member
iTrader: (8)
 
Joined: Jun 2003
Posts: 1,057
Likes: 6
From: san mateo
Default

You can check the MAF sensor. If it is unplugged or damage it can cause similar symptoms. GL
Reply
Old Jul 25, 2009 | 09:09 PM
  #4  
z2g's Avatar
z2g
Registered User
iTrader: (20)
 
Joined: Feb 2006
Posts: 1,014
Likes: 0
From: louisiana
Default

Originally Posted by gabe3d
You can check the MAF sensor. If it is unplugged or damage it can cause similar symptoms. GL
Yea sounds like a maf problem
Reply
Old Jul 26, 2009 | 07:50 PM
  #5  
kpowell's Avatar
kpowell
Registered User
 
Joined: Mar 2005
Posts: 6
Likes: 0
From: Southern California
Default

No, I have just strated and driven it every weekend since 2004.
Drove it last weekend. Then after sitting a week it just wont run above 2,500 rpm now.
The Check Engine soon light is on.
Reply
Old Jul 26, 2009 | 09:54 PM
  #6  
z2g's Avatar
z2g
Registered User
iTrader: (20)
 
Joined: Feb 2006
Posts: 1,014
Likes: 0
From: louisiana
Default

Get it scanned for codes and see what you get and then go from there
Reply
Old Sep 6, 2009 | 12:37 AM
  #7  
kaotikghost's Avatar
kaotikghost
Registered User
 
Joined: Jul 2008
Posts: 8
Likes: 0
From: Guam
Default

I recently came across this problem. But for me, everything was goin well till I ran over a little pothole then I noticed my car bogs out at 2k rpm feels almost like the rev limiter. So I take a look around and I find my oil is low and the leak is coming fro
my (looks like a valve cover). I'm now tryin to find out how to change my valve cover gasket. Does anyone know if backyard mechanic skills is enough skills to replace a valve cover gasket? Or might it be best for me to have a shop do it? By the way, where is this maf sensor located? I might want to scope that out cause it was after I hit the pothole when all my problems occured.

Thanks for the help
Reply
Old Sep 8, 2009 | 12:01 AM
  #8  
Hostetler's Avatar
Hostetler
Registered User
iTrader: (3)
 
Joined: Jan 2008
Posts: 140
Likes: 0
From: New Tampa,FL
Default

Disconnect the neg. cable on the battery. let sit for 2 min and reconnect. start the car and test. Mine did the same thing when I went through a car wash and drenched my air filter with water.
Reply
Old Sep 9, 2009 | 02:13 PM
  #9  
Acidhex's Avatar
Acidhex
New Member
 
Joined: Nov 2008
Posts: 100
Likes: 0
From: place
Default

It almost sounds like a MAF sensor problem - but IIRC Safe Mode is 1500rpm max. Sounds like something else to me.
Reply
Old Dec 19, 2010 | 07:14 AM
  #10  
wwwbret's Avatar
wwwbret
Registered User
 
Joined: Dec 2010
Posts: 1
Likes: 0
From: NJ
Default

I know this is an old thread but wanted to convey what happened to me as it may be a help for others.

Came out of car wash w/ my '08 G35, car stalled, engine would barely start, really rough 500 rpm. Giving it gas didn't do anything. Opening the hood saw that water had definitely got in the engine bay. Buildup of leaves may have made it worse. I left the car for about 1 hour with the hood up. Got car to start but was in that limp mode & would only go 2500 rpms. After leaving it for another 2 hours, it was ok again. Also put some HEET in it to be sure. May save other folks from a tow & expensive mechanic visit.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
liqalu04
Engine & Drivetrain
31
Jan 2, 2022 12:58 PM
Fixxxercask
Engine
6
Nov 9, 2015 11:10 AM
MicVelo
NorCal Marketplace
9
Oct 4, 2015 07:55 PM




All times are GMT -8. The time now is 03:45 AM.