Notices

Idle RPM's jumping up & down

Thread Tools
 
Search this Thread
 
Old Jun 1, 2022 | 05:46 PM
  #1  
brandythez's Avatar
brandythez
Thread Starter
New Member
 
Joined: Jun 2022
Posts: 2
Likes: 0
From: New York
Default Idle RPM's jumping up & down

i've owned my Z for about 7 months now & I just recently put my cat-back exhaust on. however, even before, i had noticed that at idle, w/o ac on, the rpm
hovers just a sliver below 750 but jumps up & down & w/ ac on, it does the same but just above 750. i know nissan says operating rpm is between like 625-750 if i'm correct, but i just wasn't sure if the jumping is normal or if an idle relearn/new parts were needed. any and all help is appreciated!!
Reply
Old Jun 2, 2022 | 09:18 AM
  #2  
jhc's Avatar
jhc
General & Tech Moderator
MY350Z.COM
Premier Member
 
Joined: Jan 2013
Posts: 10,400
Likes: 2,226
From: ZdayZ
Default

Originally Posted by brandythez
i've owned my Z for about 7 months now & I just recently put my cat-back exhaust on. however, even before, i had noticed that at idle, w/o ac on, the rpm
hovers just a sliver below 750 but jumps up & down & w/ ac on, it does the same but just above 750. i know nissan says operating rpm is between like 625-750 if i'm correct, but i just wasn't sure if the jumping is normal or if an idle relearn/new parts were needed. any and all help is appreciated!!
Welcome,
If your idle is surging, meaning starts low and raises up and repeats you likely have a vacuum leak somewhere. Anything changed in front of the throttle body?
Reply
Old Jun 3, 2022 | 09:11 PM
  #3  
brandythez's Avatar
brandythez
Thread Starter
New Member
 
Joined: Jun 2022
Posts: 2
Likes: 0
From: New York
Default

Originally Posted by jhc
Welcome,
If your idle is surging, meaning starts low and raises up and repeats you likely have a vacuum leak somewhere. Anything changed in front of the throttle body?
Yeah I changed the MAF sensor a few months ago but I did an ECU reset & an idle relearn. My guts leading more towards vacuum leak, where would you suggest i look first?
Reply
Old Jun 4, 2022 | 05:14 PM
  #4  
jhc's Avatar
jhc
General & Tech Moderator
MY350Z.COM
Premier Member
 
Joined: Jan 2013
Posts: 10,400
Likes: 2,226
From: ZdayZ
Default

Originally Posted by brandythez
Yeah I changed the MAF sensor a few months ago but I did an ECU reset & an idle relearn. My guts leading more towards vacuum leak, where would you suggest i look first?
If the hoses (ALL) coming off the intake manifold are old or powdery, replace withe correct size, it's cheap. Usually Nissan gaskets are good until you try to reuse them so I wouldn't immediately suspect an intake manifold gasket. Buy/borrow a vacuum Guage from AutoZone or O'Reilly and hook it up. The reading should be quite steady at 22 or above. If the needle move wildly with rpm changes you know there's a leak.
Gl!
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
CocochickenOP
Engine & Drivetrain
1
Apr 9, 2022 03:20 PM
shadykilla717
VQ35HR
18
Jan 14, 2008 02:54 PM
Zyclone Z
Engine & Drivetrain
13
Dec 29, 2007 12:45 PM
Jokestrap
Engine & Drivetrain
21
Jan 12, 2007 04:30 PM
gtbuzzbee
Engine & Drivetrain
7
Aug 23, 2003 09:53 PM




All times are GMT -8. The time now is 10:09 PM.