Water/Methanol Injection install 350z
#1
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
Water/Methanol Injection install 350z
Snow performance Boost Cooler Stage II #20010
I threw out the hardware that came with the kit. Used self tapping screws.
Nylon tubing way to short. Bought longer tubing.
Used a different led light.
Black box is hidden in the battery Bay.
Excuse all the extra wires hanging in the floor board.
Hope these pic's help on any ideas.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
I threw out the hardware that came with the kit. Used self tapping screws.
Nylon tubing way to short. Bought longer tubing.
Used a different led light.
Black box is hidden in the battery Bay.
Excuse all the extra wires hanging in the floor board.
Hope these pic's help on any ideas.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
Last edited by frankie945; 07-30-2008 at 01:13 PM.
#3
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by carfi179
Any before and after dyno comparison? what water/meth mix your using?
#5
Registered User
iTrader: (1)
Nice install. good job man..
I have few questions though;
1. what is the black box?
2. I assume the unit on the floor matt is the snow performance controller, no?
3. does the Reservoir tank have to be higher than the pump? reason?
4. the LED light indicates when you have a low level right? why did you change it?
5. I see that you are running 2 lines, 1 is white and the other is green, what are they?
6. are you using the nozzles that came with the kit? what size are they?
7. where did you get the kit from and for how much?
I have few questions though;
1. what is the black box?
2. I assume the unit on the floor matt is the snow performance controller, no?
3. does the Reservoir tank have to be higher than the pump? reason?
4. the LED light indicates when you have a low level right? why did you change it?
5. I see that you are running 2 lines, 1 is white and the other is green, what are they?
6. are you using the nozzles that came with the kit? what size are they?
7. where did you get the kit from and for how much?
The following users liked this post:
dkatkins (08-07-2020)
#6
New Member
iTrader: (11)
1. the controller
2. thats the UTEC Tuna
3. shurflo pumps dont create alot of suction, they run best gravity fed
4. led is usually wired to show when the pump is on, there is no low level indicator in his pics. thats another 20$ option
5. i would bet the green line is the stock rear window pisser line
2. thats the UTEC Tuna
3. shurflo pumps dont create alot of suction, they run best gravity fed
4. led is usually wired to show when the pump is on, there is no low level indicator in his pics. thats another 20$ option
5. i would bet the green line is the stock rear window pisser line
#7
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by str8dum1
1. the controller
2. thats the UTEC Tuna
3. shurflo pumps dont create alot of suction, they run best gravity fed
4. led is usually wired to show when the pump is on, there is no low level indicator in his pics. thats another 20$ option
5. i would bet the green line is the stock rear window pisser line
2. thats the UTEC Tuna
3. shurflo pumps dont create alot of suction, they run best gravity fed
4. led is usually wired to show when the pump is on, there is no low level indicator in his pics. thats another 20$ option
5. i would bet the green line is the stock rear window pisser line
Trending Topics
#9
Registered User
iTrader: (10)
Join Date: Jun 2004
Location: Yonkers NY
Posts: 862
Likes: 0
Received 0 Likes
on
0 Posts
nice i also have a procharger and i am relocating the maf to move the nozzle further from the TB i thought it had to be 6-9 inches away the vari-cool kit i have recomends right after the ICany numbers on this?
#10
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Ep3
nice i also have a procharger and i am relocating the maf to move the nozzle further from the TB i thought it had to be 6-9 inches away the vari-cool kit i have recomends right after the ICany numbers on this?
#12
OGPremierMafia
iTrader: (16)
Join Date: Feb 2005
Location: Cincinnati OH
Posts: 5,106
Likes: 0
Received 0 Likes
on
0 Posts
Meth users, windhield washer fluid sucks, it will yield the same results 90% but it has detergents and those dont break down as well in the heat.
Either use Distilled water with M1 Meth or just Distilled H20 to reduce knock.
Either use Distilled water with M1 Meth or just Distilled H20 to reduce knock.
#13
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by gsxrjohn
I have another question. Why did you remove your spare then replace it with a 25lbs weight?
Nice job though!
Nice job though!
Last edited by frankie945; 05-20-2008 at 08:08 AM.
#14
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MI 35th
Meth users, windhield washer fluid sucks, it will yield the same results 90% but it has detergents and those dont break down as well in the heat.
Either use Distilled water with M1 Meth or just Distilled H20 to reduce knock.
Either use Distilled water with M1 Meth or just Distilled H20 to reduce knock.
#16
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
The black box works great I start spraying at 2 psi. And it's real easy to setup you just dial in the boost which u want to start spraying and how much. There is only 2 adjustments.
Last edited by frankie945; 05-20-2008 at 01:21 PM.
#18
FREEDOM FIGHTER
iTrader: (33)
Join Date: Jan 2008
Location: !!!Viva Las Vegas!!!
Posts: 351
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by frankie945
Need traction = more weight. and couldn't keep spare the pump is in the way, who needs it anyway.
it would be nice to get a bigger container huh? I guess we don't have any other space to put the meth/alc kit around the engine bay? hmmm... this will be my upgrade along with a procharger...
Last edited by Bumble_Zee; 06-12-2008 at 12:47 PM.
#20
Registered User
Thread Starter
iTrader: (35)
Join Date: Nov 2007
Location: louisvile KY
Posts: 852
Likes: 0
Received 0 Likes
on
0 Posts
Snow performance has just upgraded there nozzles to all steel so you wont have to worry about the nozzle blowing apart. If you have a plastic one and won't a steel nozzle just send Snow performance a email and they will take care of you for free. Just a little update....